<div dir="ltr"><div><div>oh for fucks sake<br><br></div>whatever<br><br><br></div></div><div class="gmail_extra"><br><div class="gmail_quote">On Mon, Jul 18, 2016 at 12:59 PM, Tim E. Real <span dir="ltr"><<a href="mailto:termtech@rogers.com" target="_blank">termtech@rogers.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">On Monday, July 18, 2016 10:30:47 AM EDT Robert Edge wrote:<br>
> Do whatever you want.  I can't explain it to you any more clearly.<br>
><br>
> On Mon, Jul 18, 2016 at 10:25 AM, Len Ovens <<a href="mailto:len@ovenwerks.net">len@ovenwerks.net</a>> wrote:<br>
> > On Sun, 17 Jul 2016, Robert Edge wrote:<br>
> ><br>
> > If you don't believe me, do this simple test:<br>
> >> feed a 1kHz tone in to the input<br>
<br>
I already said that I did that and verified it works.<br>
<br>
Unless MAudio had started to make these cards without<br>
 a volume control chip, your distortion is upstream,<br>
 not from the 1010LT card.<br>
Or the card is not being used correctly. Check your settings.<br>
Are you sure the Patchbay/Router tab settings are correct?<br>
Or... your card has a partially fried preamplifier IC? Hey, it happens.<br>
<br>
This card has an ak4*** chip with full analog attenuator and amplifier.<br>
<br>
(And, uh... if /you/ don't believe /me/ then look at the 'About' tab<br>
 in Mudita24 and see who one of the authors is.)<br>
<br>
But seriously, I hope this helps in better understanding the card and<br>
 tracking down the real source of the distortion, which cannot be<br>
 a properly functioning card.<br>
<br>
Tim.<br>
<br>
<br>
> >><br>
> >> set 'analog volume' control in software to 0dB<br>
> >><br>
> >> connect to ardour or your choice of recorder with decent metering.  set<br>
> >> meter<br>
> >> point to 'in'<br>
> >><br>
> >> increase volume of test signal until you are getting 0dBFS.  no matter<br>
> >> how much<br>
> >> you increase the level of the test signal from here it will continue to<br>
> >> read<br>
> >> 0dbFS.  turn the signal generator up a good few dB so you are well in to<br>
> >> clipping.<br>
> >><br>
> >> record a bit of this.  you will see a squared off wave.<br>
> >><br>
> >> now turn down the 'analog volume' control until you are seeing a nice<br>
> >> comfortable<br>
> >> level.  do not change the level of the test signal generator.<br>
> >><br>
> >> record again.<br>
> >><br>
> >> the result will still be clipped.<br>
> >><br>
> >> in fact it will be identical to the first signal you recorded, just<br>
> >> scaled down.<br>
> >><br>
> >> I mean, you guys do whatever you want, but that is what is actually<br>
> >> happening in<br>
> >> your signal chain.<br>
> ><br>
> > How do you know this is digital and not analog clipping? The result would<br>
> > look the same.<br>
> ><br>
> > signal path:<br>
> ><br>
> > AC -> resitor -> buffer -> digitally -> ADC<br>
> > in    pad on     amp       controlled<br>
> ><br>
> >       card                 analog gain<br>
> ><br>
> > if the input signal after the input pad has p-p higher than amp's power<br>
> > rails allow, the signal will be squared off, just as you are seeing. The<br>
> > gain stage would be a part of the ADC chip BTW. The buffer amp is probably<br>
> > not, but rather a gain stage added to allow the use of mic level inputs.<br>
> > (M-Audio advertise it as a Mic Pre)<br>
> ><br>
> > --<br>
> > Len Ovens<br>
> > <a href="http://www.ovenwerks.net" rel="noreferrer" target="_blank">www.ovenwerks.net</a><br>
<br>
<br>
_______________________________________________<br>
Linux-audio-user mailing list<br>
<a href="mailto:Linux-audio-user@lists.linuxaudio.org">Linux-audio-user@lists.linuxaudio.org</a><br>
<a href="http://lists.linuxaudio.org/listinfo/linux-audio-user" rel="noreferrer" target="_blank">http://lists.linuxaudio.org/listinfo/linux-audio-user</a><br>
</blockquote></div><br></div>