[linux-audio-user] Re: Tascam US-122 and Debian

[karsten wiese]

--- Björn Lindström <bkhl at elektrubadur.se> schrieb:

> karsten wiese <annabellesgarden at yahoo.de>:
> 
> > Above error message means:
> > "usx2yloader can't transfer the firmware to the us122"
> >
> > So it could be a USB problem.  I once had such USB problem with a
> > VIA chipset mobo.  things didn't work, until i connected my us428 to
> > the other USB connector.
> >
> > Does
> >     $ dmesg
> > say something?
> 
> Nothing very interesting. This is what comes from loading the module
> and running fxload:
> 
>   usbcore: registered new driver snd-usb-usx2y
>   usb 2-2: USB disconnect, address 23
>   usb 2-2: new full speed USB device using uhci_hcd and address 24
> 
> > what kind of motherboard do you use?
> > Please post outputs of
> >     $ lspci
> 
> The computer is an IBM ThinkPad R40. The lspci output is as follows:
> 
> 0000:00:00.0 Host bridge: Intel Corporation 82845 845 (Brookdale) Chipset Host Bridge (rev 04)
> 0000:00:01.0 PCI bridge: Intel Corporation 82845 845 (Brookdale) Chipset AGP Bridge (rev 04)
> 0000:00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
> Controller #1 (rev 03)
> 0000:00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
> Controller #2 (rev 03)
> 0000:00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
> Controller #3 (rev 03)
> 0000:00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller
> (rev 03)
> 0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83)
> 0000:00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
> 0000:00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03)
> 0000:00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev
> 03)
> 0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
> AC'97 Audio Controller (rev 03)
> 0000:00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem
> Controller (rev 03)
> 0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY
> 0000:02:00.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus Controller
> 0000:02:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)
> 0000:02:07.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller
> (PHY/Link)
> 0000:02:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (MOB) Ethernet Controller
> (rev 83)
> 
> I hope you can make something of this.

can't ;-)
that usx2yloader error should only happen,
if something has gone to "dmesg" as well.
the chipset is not like the one, i had trouble with.

me thinks it'd be best to compile/install a recent kernel
with CONFIG_SND_DEBUG_DETECT set and check if dmesg shows
something ( like "dsp_load") then.



	

	
		
___________________________________________________________ 
Telefonate ohne weitere Kosten vom PC zum PC: http://messenger.yahoo.de