[linux-audio-dev] linux 2.6.1 realtime lsm, jackstart & ecasound success

I just completed a successful run of ecasound with my guitar_mix.ecs (attached) on my new box. This is a 15 minutes 5 track session, 4 tracks from disk, one live jack input. Three outputs: stereo wav, mono wav and live monitor. It uses amplify and panning effects controlled by ecasound generic oscillators. Details on the new box and it's current configuration: asus a7v8x-x athlon XP 2800+ (2071.203 MHz) 1.5GB PC2700 RAM 12GB / /dev/hda2 (actually a 40G disk) 160GB /mnt/audio/ /dev/hdc1 drives tuned 2GB swap /dev/hda1 onboard via8235 (M-Audio Delta-66 w/omni i/o -- still in old box) (ymfpci guillemot maxisound fortissimo -- midi only -- still in old box) debian testing (sarge) 2.6.1 (pre-empt on -- kernel.org sources compiled via make-kpkg) realtime-0.0.2 lsm alsa-1.0.2 (drivers, lib, envy24control, tools) drivers: ./configure --with-isapnp=no --with-sequencer=yes --with-oss=no \ --with-cards=dummy,virmidi,ice1712,ymfpci,via82xx libsndfile-1.0.5 from tar.gz. debian only had 1.0.4 jack-0.94.0 ./configure --enable-capabilities --enable-optimize \ --with-default-tmpdir=/mnt/ramfs/ --disable-portaudio ecasound-2.3.2 ./configure --enable-pyecasound --disable-oss --disable-arts \ --with-largefile I started jackd via jackstart like so: jackstart -v -R -d alsa -d via82xx -r 44100 -p 128 -n 3 I run the ecasound session from a script that does some pre and post processing. It assembles the 4 wav input files from other wav's and cuts the output files down to randomly selected 5 minute chunks, fades in and out the beginnings and ends, normalizes and encodes the stereo wav to ogg. The whole session ran on this onboard soundcard without xruns. I switched desktops numerous times in openbox3 and even switched out of X to tty2 to login and change my hostname back (I had changed it while in X and new apps weren't able to start because they couldn't connect to the display. duh ... 8) ). The session ran flawlessly. I'm not exactly sure what the stats jackd puts out when run verbosely mean, but I know the results I saw mean I'll be able to run this session with many more effects at lower latency than I could on my old box ... _And_ I don't have to do it as root! yay! :) The old box is a PII 400 w/768M PC100 RAM. On that box the whole session including pre and post processing takes around 21 minutes. On the new box that overhead is cut way down with the whole session taking only 16 minutes 20 seconds (only 1 min, 20 more than the actual recording time). While running jackd reports load averaging (just measured visually from jackd output, not hard numbers) around 7.5 with max usecs ~220. On the old box using my delta66 I have to run at -p 256 to avoid xruns in this session, load averages around 22 and max usecs around 1350. Admittedly, much of this performance gain is related to the new hardware. But, still , it's very cool that all this newish stuff (lsm, latest alsa, latest ecasound, latest jackd, 2.6 kernel) is working well In other testing with the via chip I've had jack running as low as -p 32 -n 3 with just a couple jack_metro's connected. I have to go down to -p 16 to get a few xruns. Not until -p 8 do things start to get really bad. /proc/interrupts says the card's on IRQ 4, too. I have a few more things to install, configure and test before I move my delta66 and midi setup over to the new box. But, these initial tests are very exciting. I just had to share. Thank you to all the developers for all this excellent software. And thanks to all the list members, too. :) -Eric Rz. # eric(a)zhevny.com guitar_mix chainsetup file ### general -b:128 -B:rtlowlatency -n:guitar_mix -X -t:902.802 ### audio inputs -a:1,6,11 -i:track1.wav -a:2,7,12 -i:track2.wav -a:3,8,13 -i:track3.wav -a:4,9,14 -i:track4.wav -a:5,10,15 -i:jack_alsa #-a:5,10,15 -f:16,1,44100 -i alsahw,0 ### audio outputs # live output -a:1,2,3,4,5 -f:16,2,44100 -o jack_alsa #-a:1,2,3,4,5 -f:16,2,44100 -o alsahw,0,0 # file outputs ### FIXME: change this output to .ogg when crop and fades work -a:6,7,8,9,10 -f:16,2,44100 -o:/mnt/audio/in_progress/guitar_mix/stereo_out.wav -a:11,12,13,14,15 -f:16,1,44100 -o:/mnt/audio/in_progress/guitar_mix/mono_out.wav ### chain operators and controllers # live output -a:1 -erc:1,2 -epp:0 -kos:1,0,100,0.02,0 -ea:0 -kos:1,0,200,0.01,0 -a:2 -erc:1,2 -epp:0 -kos:1,0,100,0.04,0 -ea:0 -kos:1,0,200,0.02,0 -a:3 -erc:1,2 -epp:0 -kos:1,0,100,0.06,0 -ea:0 -kos:1,0,200,0.03,0 -a:4 -erc:1,2 -epp:0 -kos:1,0,100,0.08,0 -ea:0 -kos:1,0,200,0.04,0 -a:5 -erc:1,2 -epp:50 -ea:205 # stereo file out for .ogg -a:6 -erc:1,2 -epp:0 -kos:1,0,100,0.02,0 -ea:0 -kos:1,0,200,0.01,0 -a:7 -erc:1,2 -epp:0 -kos:1,0,100,0.04,0 -ea:0 -kos:1,0,200,0.02,0 -a:8 -erc:1,2 -epp:0 -kos:1,0,100,0.06,0 -ea:0 -kos:1,0,200,0.03,0 -a:9 -erc:1,2 -epp:0 -kos:1,0,100,0.08,0 -ea:0 -kos:1,0,200,0.04,0 -a:10 -erc:1,2 -epp:50 -ea:205 ### crop and fade in/out ### generate an effects preset file for this in preprocessing #-a:6,7,8,9,10 -ea:0 -kl:1,0,100,4,0,0,10,1,290,1,300,0 # mono file out for pool -a:11 -ea:0 -kos:1,0,200,0.01,0 -a:12 -ea:0 -kos:1,0,200,0.02,0 -a:13 -ea:0 -kos:1,0,200,0.03,0 -a:14 -ea:0 -kos:1,0,200,0.04,0 -a:15 -ea:205 ### crop and fade in/out ### generate an effects preset file for this in preprocessing #-a:11,12,13,14,15 -gc:$pos,300 -ea:100 -klg:0,0,100,4,0,0,10,1,290,1,300,0