15 Aug
2015
15 Aug
'15
3:01 p.m.
Hello.
I would like to sync the arpeggiator from a Korg Microstation to
Ardour. The user guide says:
"the arpeggiator will synchronize to the MIDI Clock and Start
messages received from a connected MIDI device."
The audio card is a 1010LT. The Microstation is connected through USB
and is fully seen in jack (qjackctl). Is it possible to have MIDI sync
for the external synth ? How would the wiring be done ? Will there be a
need for an Ardour MIDI track for the Start (and possibly Stop)
signals ?
Thanks.
15 Aug
15 Aug
3:24 p.m.
On Sat, 15 Aug 2015, jonetsu(a)teksavvy.com wrote:
I would like to sync the arpeggiator from a Korg
Microstation to
Ardour. The user guide says:
"the arpeggiator will synchronize to the MIDI Clock and Start
messages received from a connected MIDI device."
The audio card is a 1010LT. The Microstation is connected through USB
and is fully seen in jack (qjackctl). Is it possible to have MIDI sync
for the external synth ? How would the wiring be done ? Will there be a
need for an Ardour MIDI track for the Start (and possibly Stop)
signals ?
Ardour already has a "MIDI clock out" You should be able to "mix" this
with the midi stream going to the korg if you are using jack midi.
Connect your normal midi out to the 1010 port going to the korg and then
connect MIDI clock out to the same 1010 port.
If you are not using a midi channel to do the actual note press input then
it is only one connection.
Note: I don't have the devices in question so I am just theorizing.
--
Len Ovens
www.ovenwerks.net
24 Aug
24 Aug
7:01 p.m.
On Sat, 15 Aug 2015 08:22:43 -0700 (PDT)
Len Ovens <len(a)ovenwerks.net> wrote:
On Sat, 15 Aug 2015, jonetsu(a)teksavvy.com wrote:
Hmmmm.. The 1010LT has MIDI in and out jacks. Currently not used since
the Korg is connected using USB. In Qjackctl's MIDI pane I see Ardour's
various MIDI connections, MMC, MTC, although in Qjackctl's MIDI pane,
Ardour is by itself. There's nothing else to connect to.
In Qjackctl's ALSA pane there is a 1010LT MIDI out as well as as Korg
MIDI in. Connecting these two does not bring over any sync.
What is this 'jack midi' you have mentioned ?
Is it possible at all to have the MIDI clock signal carried over to the
Korg while only using the USB connector to the Korg ?
Cheers.
I would like to sync the arpeggiator from a Korg
Microstation to
Ardour. The user guide says:
"the arpeggiator will synchronize to the MIDI Clock and Start
messages received from a connected MIDI device."
The audio card is a 1010LT. The Microstation is connected through
USB and is fully seen in jack (qjackctl). Is it possible to have
MIDI sync for the external synth ? How would the wiring be done ?
Will there be a need for an Ardour MIDI track for the Start (and
possibly Stop) signals ?
Ardour already has a "MIDI clock out" You should be able to "mix"
this with the midi stream going to the korg if you are using jack
midi. Connect your normal midi out to the 1010 port going to the korg
and then connect MIDI clock out to the same 1010 port.
If you are not using a midi channel to do the actual note press input
then it is only one connection.
Note: I don't have the devices in question so I am just theorizing.
7:14 p.m.
On Mon, 24 Aug 2015, jonetsu(a)teksavvy.com wrote:
On Sat, 15 Aug 2015 08:22:43 -0700 (PDT)
Len Ovens <len(a)ovenwerks.net> wrote:
My mistake, I saw the 1010 and just figured that was what you are using
for MIDI. However, the same applies to a USB midi. Your korg should also
show up in the MIDI panel. If you are seeing only Ardour in your MIDI
panel of the qjackctl connections window, You probably need to run
a2jmidid. The command to use is:
a2j_control ehw start
This should be run after jack is already running. It can be added to
qjackctl's Setup->Options page in the "Execute script after Startup:".
It will stop all on it's own when jack goes away.
On Sat, 15 Aug 2015, jonetsu(a)teksavvy.com wrote:
Hmmmm.. The 1010LT has MIDI in and out jacks. Currently not used since
the Korg is connected using USB. In Qjackctl's MIDI pane I see Ardour's
various MIDI connections, MMC, MTC, although in Qjackctl's MIDI pane,
Ardour is by itself. There's nothing else to connect to. Ardour. The user guide says:
"the arpeggiator will synchronize to the MIDI Clock and Start
messages received from a connected MIDI device."
The audio card is a 1010LT. The Microstation is connected through
USB and is fully seen in jack (qjackctl). Is it possible to have
MIDI sync for the external synth ? How would the wiring be done ?
Will there be a need for an Ardour MIDI track for the Start (and
possibly Stop) signals ?
Ardour already has a "MIDI clock out" You should be able to "mix"
this with the midi stream going to the korg if you are using jack
midi. Connect your normal midi out to the 1010 port going to the korg
and then connect MIDI clock out to the same 1010 port.
If you are not using a midi channel to do the actual note press input
then it is only one connection.
Note: I don't have the devices in question so I am just theorizing. What is this 'jack midi' you have mentioned ?
a2jmidid will connect ALSA to MIDI. The MIDI tab in qjackctl is jack MIDI
and the ALSA tab is alsa midi.
--
Len Ovens
www.ovenwerks.net
3826
days inactive
3835
days old
linux-audio-user@lists.linuxaudio.org
3 comments
2 participants
participants (2)
-
jonetsu＠teksavvy.com -
Len Ovens