28 Sep
2005
28 Sep
'05
4:26 p.m.
Hi all,
I have a fully up-to-date PlanetCCRMA FC3 machine - 700Mhz P3 with about
640MB of RAM.
I bought a cheap second-hand RME Hammerfall 9636 recently, in the
knowledge that it was untested.
I've plugged the card in, and run alsaconf. I can start jack with
qjackctl, and connect my audio applications to all of the cards inputs
and outputs, and so on.
I have a Behringer ADA8000 connected to the first lightpipe output.
However, I'm having difficulties getting a clean output - whichever
software I use...
For example, when I play audio, and route it to output 1, all I can hear
is some approximation of white noise, until the volume gets to somewhere
near maximum - when I can hear a very distorted version of the original
sound.
Does this help at all?
I'm *hoping* that I've just done something wrong, and that the card
isn't fried. ALSA detected the card fine though, for what it's worth.
Regards,
Michael
28 Sep
28 Sep
4:56 p.m.
Hi Michael,
Sorry for the troubles...
On 9/28/05, Michael T D Nelson <m_nels(a)gmx.net> wrote:
Hi all,
I have a fully up-to-date PlanetCCRMA FC3 machine - 700Mhz P3 with about
640MB of RAM.
I bought a cheap second-hand RME Hammerfall 9636 recently, in the
knowledge that it was untested.
OK...
I've plugged the card in, and run alsaconf. I can start jack with
qjackctl, and connect my audio applications to all of the cards inputs
and outputs, and so on.
Sounds good so far.
I have a Behringer ADA8000 connected to the first lightpipe output.
The ADA8000 has two ADAT cables, correct? Have you connected both of
them? Does the ADA8000 have clock rate indicators? Does the clock rate
follow the rate you set in QJackCTL?
However, I'm having difficulties getting a clean output - whichever
software I use...
For example, when I play audio, and route it to output 1, all I can hear
is some approximation of white noise, until the volume gets to somewhere
near maximum - when I can hear a very distorted version of the original
sound.
Does this help at all?
A bit. I thought we were supposed to be able to look at this cards
settings using amixer but so far it shows me nothing for the 9636
while it shows me lots for the AP2496. I'll look at that a bit more
but maybe you know how to use amixer or have some better info on this?
Basically I'm thinking we need to see the card's settings...
I'm *hoping* that I've just done something wrong, and that the card
isn't fried. ALSA detected the card fine though, for what it's worth.
I have a 9636 (same card) with all 4 ADAT cables going to two I/Os on
my HDSP 9652.
I always watch the 9636 indirectly by using hdspconf on the HDSP 9652
end. It just works and I don't have issues.
Wish I could be of more help.
5:11 p.m.
On Wed, 2005-09-28 at 21:26 +0100, Michael T D Nelson wrote:
I bought a cheap second-hand RME Hammerfall 9636
recently, in the
knowledge that it was untested.
first step, pull the card, look for a small chip that will say either
"W36" or "M36". find out which one it is.
i (yes, even i!) had problems with this when accidentally using a 9636
with the little-endian EPROM ("W36") on a big-endian machine (a mac).
I've plugged the card in, and run alsaconf. I can
start jack with
qjackctl, and connect my audio applications to all of the cards inputs
and outputs, and so on.
I have a Behringer ADA8000 connected to the first lightpipe output.
how are you sharing the sample clock between the two? hdspconf is the
app to manage this ...
5:18 p.m.
Thanks for the speedy response!
Mark Knecht wrote:
Good point. I actually *did* find this, but it was after I wrote the
email last night (I didn't send it straight away!)
I'll look into this again tomorrow, and get back to you...
[I had to work late today. I was installing an 8 serial port DigiBoard
into a dual Xeon server running RedHat 9. We hit all sorts of problems.
It turned out that the bloody server was just too damn fast for it's own
good, so I've got to cook up a way to delay some of my startup scripts.
Then I was stuck in traffic for three hours.]
It's just nice to know that someone cares enough to try! You've helped
me clarify my thoughts a little already. I'm sure I'll get there eventually.
Thanks very much
Michael Nelson
Hi Michael,
Sorry for the troubles...
On 9/28/05, Michael T D Nelson <m_nels(a)gmx.net> wrote:
Yes. There is one from the ADA8000 to the RME 9636, and one in the other
direction.
Hi all,
I have a fully up-to-date PlanetCCRMA FC3 machine - 700Mhz P3 with about
640MB of RAM.
I bought a cheap second-hand RME Hammerfall 9636 recently, in the
knowledge that it was untested.
OK...
I've plugged the card in, and run alsaconf. I
can start jack with
qjackctl, and connect my audio applications to all of the cards inputs
and outputs, and so on.
Sounds good so far.
I have a Behringer ADA8000 connected to the first
lightpipe output.
The ADA8000 has two ADAT cables, correct? Have you connected both of
them? Does the ADA8000 have clock rate indicators? Does the clock rate
follow the rate you set in QJackCTL?
However, I'm having difficulties getting a
clean output - whichever
software I use...
For example, when I play audio, and route it to output 1, all I can hear
is some approximation of white noise, until the volume gets to somewhere
near maximum - when I can hear a very distorted version of the original
sound.
Does this help at all?
A bit. I thought we were supposed to be able to look at this cards
settings using amixer but so far it shows me nothing for the 9636
while it shows me lots for the AP2496. I'll look at that a bit more
but maybe you know how to use amixer or have some better info on this?
Basically I'm thinking we need to see the card's settings... I'm
*hoping* that I've just done something wrong, and that the card
isn't fried. ALSA detected the card fine though, for what it's worth.
I have a 9636 (same card) with all 4 ADAT cables going to two I/Os on
my HDSP 9652.
I always watch the 9636 indirectly by using hdspconf on the HDSP 9652
end. It just works and I don't have issues.
Wish I could be of more help.
6:41 p.m.
On 9/28/05, Paul Davis <paul(a)linuxaudiosystems.com> wrote:
On Wed, 2005-09-28 at 21:26 +0100, Michael T D Nelson
wrote:
Does hdspconf work for the Hammerfall? I think it's just for the HDSP
line, correct?
Anyway, it doesn't work on my 9636 machine here.
I've plugged the card in, and run alsaconf. I
can start jack with
qjackctl, and connect my audio applications to all of the cards inputs
and outputs, and so on.
I have a Behringer ADA8000 connected to the first lightpipe output.
how are you sharing the sample clock between the two? hdspconf is the
app to manage this ...
29 Sep
29 Sep
4 a.m.
Thanks also for the prompt reply Paul!
Paul Davis wrote:
Like Mark, I thought that hdspconf was just for the newer HDSP cards.
This is a Hammerfall Light 9636. Are we wrong?
At the moment, I'm either setting the switch on the ADA8000 to 'Master',
or to 'Slave: ADAT in'. On either setting, the 'Sync locked' light on
the ADA8000 turns on.
Thanks
Michael
On Wed, 2005-09-28 at 21:26 +0100, Michael T D Nelson
wrote:
I'll do this later, when I've got some work done...
This does sound as though it might be the cause of my problem. The card
*was* previously in a Mac - I asked on this list earlier whether it
would be compatible, and someone said it was. I probably wasn't very clear.
Is that the chip that sits in a slot on the card? Is it an EPROM that I
can get hold of and replace myself? I seem to remember seeing chips for
RME cards labelled with different revisions on eBay...
I bought a cheap second-hand RME Hammerfall 9636
recently, in the
knowledge that it was untested.
first step, pull the card, look for a small chip that will say either
"W36" or "M36". find out which one it is.
i (yes, even i!) had problems with this when accidentally using a 9636
with the little-endian EPROM ("W36") on a big-endian machine (a mac).
I've
plugged the card in, and run alsaconf. I can start jack with
qjackctl, and connect my audio applications to all of the cards inputs
and outputs, and so on.
I have a Behringer ADA8000 connected to the first lightpipe output.
how are you sharing the sample clock between the two? hdspconf is the
app to manage this ...
3:12 p.m.
Paul Davis wrote:
On Wed, 2005-09-28 at 21:26 +0100, Michael T D Nelson
wrote:
Hello again Paul.
I think that you're right.
The EPROM is marked 'M36'. I am using it in a Pentium 3 machine. Later
it will probably be used in an Athlon XP box. I take it that this is
probably causing my problem?
Am I correct in assuming that I need to obtain a 'W36' chip and swap the
two?
Does anyone know if the revision number of the chip is significant? I
was told that the original card was revision 1.5.
Thanks for your help,
Michael Nelson
I bought a cheap second-hand RME Hammerfall 9636
recently, in the
knowledge that it was untested.
first step, pull the card, look for a small chip that will say either
"W36" or "M36". find out which one it is.
i (yes, even i!) had problems with this when accidentally using a 9636
with the little-endian EPROM ("W36") on a big-endian machine (a mac).
3:12 p.m.
Mark Knecht wrote:
I thought we were supposed to be able to look at this
cards
settings using amixer but so far it shows me nothing for the 9636
while it shows me lots for the AP2496. I'll look at that a bit more
but maybe you know how to use amixer or have some better info on this?
I've experienced exactly the same - amixer shows me lots for my cheapo
CMI8738 card, but nothing at all for the DIGI9636.
I don't know whether or not his is expected, but I think Paul Davis may
have found the answer to my problem elsewhere in this thread.
Thanks
Michael Nelson
4:57 p.m.
On 9/29/05, Michael T D Nelson <m_nels(a)gmx.net> wrote:
Paul Davis wrote:
Hi,
I would take this question to the RME forums and ask there.
http://www.rme-audio.com/english/index.htm
They are usually pretty helpful. Obviously I didn't have a clue
about this one since my 9636 works and always has, but my HDSP 9652
has been through a number of firmware revisions. For that card RME
provides an app that writes firmware updates. Unfortunately it's
Windows only so either set up to dual boot of move the card
temporarily assuming that such an app exists for the 9636. It may be
part of the driver package. Not sure.
Good luck!
- Mark
On Wed, 2005-09-28 at 21:26 +0100, Michael T D
Nelson wrote:
Hello again Paul.
I think that you're right.
The EPROM is marked 'M36'. I am using it in a Pentium 3 machine. Later
it will probably be used in an Athlon XP box. I take it that this is
probably causing my problem?
Am I correct in assuming that I need to obtain a 'W36' chip and swap the
two?
Does anyone know if the revision number of the chip is significant? I
was told that the original card was revision 1.5.
Thanks for your help,
Michael Nelson
I bought a cheap second-hand RME Hammerfall 9636
recently, in the
knowledge that it was untested.
first step, pull the card, look for a small chip that will say either
"W36" or "M36". find out which one it is.
i (yes, even i!) had problems with this when accidentally using a 9636
with the little-endian EPROM ("W36") on a big-endian machine (a mac).
5:14 p.m.
On Thu, 2005-09-29 at 13:57 -0700, Mark Knecht wrote:
On 9/29/05, Michael T D Nelson <m_nels(a)gmx.net>
wrote:
> Paul Davis wrote:
> > On Wed, 2005-09-28 at 21:26 +0100, Michael T D Nelson wrote:
> >>I bought a cheap second-hand RME Hammerfall 9636 recently, in the
> >>knowledge that it was untested.
> >
> > first step, pull the card, look for a small chip that will say either
> > "W36" or "M36". find out which one it is.
> >
> > i (yes, even i!) had problems with this when accidentally using a 9636
> > with the little-endian EPROM ("W36") on a big-endian machine (a
mac).
>
> Hello again Paul.
>
> I think that you're right.
>
> The EPROM is marked 'M36'. I am using it in a Pentium 3 machine. Later
> it will probably be used in an Athlon XP box. I take it that this is
> probably causing my problem?
>
> Am I correct in assuming that I need to obtain a 'W36' chip and swap the
> two?
>
> Does anyone know if the revision number of the chip is significant? I
> was told that the original card was revision 1.5.
1.5 is just fine. You don't need newer or older to use the card
perfectly well.
--p
18 Oct
18 Oct
1:17 p.m.
I think it's time for me to say thanks!
You hit the nail right on the head, Paul. I've just picked up a W36
EPROM for the DIGI9636, and it worked instantly.
Even on cheap little PC speakers, I can hear an improvement. Now, time
to save up for some Alesis MII active monitors...
Thank you
Michael Nelson
1:59 p.m.
HI
I was lucky with my RME as it was set for PC and worked from day one!
Its a superb card with Linux and Ardour.
I'm using the Behringer truth actives for monitors (didnt have to save a
lot, from ebay!!)
They sound good.
cheers
Bob
Michael T D Nelson wrote:
I think it's time for me to say thanks!
You hit the nail right on the head, Paul. I've just picked up a W36
EPROM for the DIGI9636, and it worked instantly.
Even on cheap little PC speakers, I can hear an improvement. Now, time
to save up for some Alesis MII active monitors...
Thank you
Michael Nelson
--
Bearmusic
hearmymusic.co.uk <http:www.hearmymusic.co.uk>
2:55 p.m.
studio-64 wrote:
HI
I was lucky with my RME as it was set for PC and worked from day one!
Its a superb card with Linux and Ardour.
Well, I'm very happy now. It's wonderful to open qjackctl and see all
those inputs and outputs lined up neatly.
I'm using the Behringer truth actives for monitors
(didnt have to save a
lot, from ebay!!)
They sound good.
Thanks for the advice. I'll try to have a listen to a pair somewhere.
That was a small error earlier - I meant Alesis M One Mk2 Actives.
The reason I'd like a pair of Mk2s is that two of my friends at
University each had them, and I really liked the way that they sound. I
have to be honest - the fact that they are made of materials like carbon
fibre and pure silk (with blue LEDs) appeals to me too!
The Behringers look comparable though (and a little cheaper too...)
Thanks
Michael Nelson
6771
days inactive
6791
days old
linux-audio-user@lists.linuxaudio.org
12 comments
4 participants
participants (4)
-
Mark Knecht -
Michael T D Nelson -
Paul Davis -
studio-64