30 Jul
2008
30 Jul
'08
1:10 p.m.
Hello,
I am a bit new to this so please bear with me. I'm trying to get my Boss GT-10 to work
on my (arch) linux install.
I added the patch that was suggested in the post I reply to to my usbquirks.h and compiled
alsa using the guide on this site:
http://www.alsa-project.org/main/index.php/Matrix:Module-usb-audio with as only difference
that I configured with '--with-cards=all'.
After this my BOSS GT-10 was recognised by linux and I am able to play sound over it using
aplay. Recording however seems not to work. When I run arecord -L it shows all three of my
audio cards, including the bossgt, but when I do alsamixer -c 2 it gives the following
error: No mixer elems found. Using a command like arecord -d 5 -t wav test.wav just gives
me the sound recorded by the microphone in another soundcard. It could be that it's
just a matter of using -D to select the right PCM, but I'm not sure how to find the
right PCM.
I suspect this is the reason I cannot record, do you have any idea what goes wrong?
Another question more out of curiosity, why does the patch specify
USB_DEVICE(0x0592,0x00da) whilst the usb device as listed by lsusb has id 0x00db?
If I need supply any specific information
With kind regards and gratitude for the patch,
Tinco Andringa
--- In reply to: ---
Clemens Ladisch cladisch at fastmail.net
Thu Jul 24 12:04:48 EDT 2008
edro Ferreira wrote:
OK, I've added the output as an attachment :).
Sorry for the delay.
Please try adding the entry below anywhere in sound/usb/usbquirks.h
and recompile the driver:
{
/* BOSS GT-10 */
USB_DEVICE(0x0582, 0x00da),
.driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
.ifnum = QUIRK_ANY_INTERFACE,
.type = QUIRK_COMPOSITE,
.data = (const struct snd_usb_audio_quirk[]) {
{
.ifnum = 0,
.type = QUIRK_AUDIO_STANDARD_INTERFACE
},
{
.ifnum = 1,
.type = QUIRK_AUDIO_STANDARD_INTERFACE
},
{
.ifnum = 2,
.type = QUIRK_MIDI_FIXED_ENDPOINT,
.data = & (const struct snd_usb_midi_endpoint_info) {
.out_cables = 0x0001,
.in_cables = 0x0001
}
},
{
.ifnum = -1
}
}
}
},
HTH
Clemens
_________________________________________________________________
Express yourself instantly with MSN Messenger! Download today it's FREE!
http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
30 Jul
30 Jul
8:01 p.m.
New subject: Boss GT-10
Hello,
The "No mixer elems found" error is normal. A for the rest, I guess
you are not correctly selecting the device for recording.
arecord --device=default:CARD=GT10 -t wav -f s16_le -r 44100 -c 2 test.wav
works for me :)
Good luck,
Pedro
On Wed, Jul 30, 2008 at 4:10 PM, Tinco Andringa <mail(a)tinco.nl> wrote:
Hello,
I am a bit new to this so please bear with me. I'm trying to get my Boss GT-10 to
work on my (arch) linux install.
I added the patch that was suggested in the post I reply to to my usbquirks.h and
compiled alsa using the guide on this site:
http://www.alsa-project.org/main/index.php/Matrix:Module-usb-audio with as only difference
that I configured with '--with-cards=all'.
After this my BOSS GT-10 was recognised by linux and I am able to play sound over it
using aplay. Recording however seems not to work. When I run arecord -L it shows all three
of my audio cards, including the bossgt, but when I do alsamixer -c 2 it gives the
following error: No mixer elems found. Using a command like arecord -d 5 -t wav test.wav
just gives me the sound recorded by the microphone in another soundcard. It could be that
it's just a matter of using -D to select the right PCM, but I'm not sure how to
find the right PCM.
I suspect this is the reason I cannot record, do you have any idea what goes wrong?
Another question more out of curiosity, why does the patch specify
USB_DEVICE(0x0592,0x00da) whilst the usb device as listed by lsusb has id 0x00db?
If I need supply any specific information
With kind regards and gratitude for the patch,
Tinco Andringa
--- In reply to: ---
Clemens Ladisch cladisch at fastmail.net
Thu Jul 24 12:04:48 EDT 2008
edro Ferreira wrote:
OK, I've added the output as an attachment
:).
Sorry for the delay.
Please try adding the entry below anywhere in sound/usb/usbquirks.h
and recompile the driver:
{
/* BOSS GT-10 */
USB_DEVICE(0x0582, 0x00da),
.driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
.ifnum = QUIRK_ANY_INTERFACE,
.type = QUIRK_COMPOSITE,
.data = (const struct snd_usb_audio_quirk[]) {
{
.ifnum = 0,
.type = QUIRK_AUDIO_STANDARD_INTERFACE
},
{
.ifnum = 1,
.type = QUIRK_AUDIO_STANDARD_INTERFACE
},
{
.ifnum = 2,
.type = QUIRK_MIDI_FIXED_ENDPOINT,
.data = & (const struct snd_usb_midi_endpoint_info) {
.out_cables = 0x0001,
.in_cables = 0x0001
}
},
{
.ifnum = -1
}
}
}
},
HTH
Clemens
_________________________________________________________________
Express yourself instantly with MSN Messenger! Download today it's FREE!
http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
_______________________________________________
Linux-audio-user mailing list
Linux-audio-user(a)lists.linuxaudio.org
http://lists.linuxaudio.org/mailman/listinfo/linux-audio-user
8:32 p.m.
New subject: Boss GT-10
Awesome thanks, that works :D So that only leaves my curiosity question, anyone got a
clue? Is this patch btw on track for inclusion in the driver? I noticed the vendor info
stuff wasn't in it so it doesn't look like a realy driver patch, I added vendor
info in my patch. I will test tomorrow if it works with the floorboard software to see if
it works with the midi stuff too.
Cheers,
Tinco
----------------------------------------
Date: Wed, 30 Jul 2008 23:01:05 +0100
From: ilzogoiby(a)gmail.com
To: mail(a)tinco.nl
Subject: Re: [LAU] Boss GT-10
CC: linux-audio-user(a)lists.linuxaudio.org
Hello,
The "No mixer elems found" error is normal. A for the rest, I guess
you are not correctly selecting the device for recording.
arecord --device=default:CARD=GT10 -t wav -f s16_le -r 44100 -c 2 test.wav
works for me :)
Good luck,
Pedro
On Wed, Jul 30, 2008 at 4:10 PM, Tinco Andringa wrote:
>
> Hello,
>
> I am a bit new to this so please bear with me. I'm trying to get my Boss GT-10 to
work on my (arch) linux install.
>
> I added the patch that was suggested in the post I reply to to my usbquirks.h and
compiled alsa using the guide on this site:
http://www.alsa-project.org/main/index.php/Matrix:Module-usb-audio with as only difference
that I configured with '--with-cards=all'.
>
> After this my BOSS GT-10 was recognised by linux and I am able to play sound over it
using aplay. Recording however seems not to work. When I run arecord -L it shows all three
of my audio cards, including the bossgt, but when I do alsamixer -c 2 it gives the
following error: No mixer elems found. Using a command like arecord -d 5 -t wav test.wav
just gives me the sound recorded by the microphone in another soundcard. It could be that
it's just a matter of using -D to select the right PCM, but I'm not sure how to
find the right PCM.
>
> I suspect this is the reason I cannot record, do you have any idea what goes wrong?
Another question more out of curiosity, why does the patch specify
USB_DEVICE(0x0592,0x00da) whilst the usb device as listed by lsusb has id 0x00db?
>
> If I need supply any specific information
>
> With kind regards and gratitude for the patch,
> Tinco Andringa
>
> --- In reply to: ---
> Clemens Ladisch cladisch at fastmail.net
>
> Thu Jul 24 12:04:48 EDT 2008
>
> edro Ferreira wrote:
>> OK, I've added the output as an attachment :).
>
> Sorry for the delay.
>
> Please try adding the entry below anywhere in sound/usb/usbquirks.h
> and recompile the driver:
>
>
> {
> /* BOSS GT-10 */
> USB_DEVICE(0x0582, 0x00da),
> .driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
> .ifnum = QUIRK_ANY_INTERFACE,
> .type = QUIRK_COMPOSITE,
> .data = (const struct snd_usb_audio_quirk[]) {
> {
> .ifnum = 0,
> .type = QUIRK_AUDIO_STANDARD_INTERFACE
> },
> {
> .ifnum = 1,
> .type = QUIRK_AUDIO_STANDARD_INTERFACE
> },
> {
> .ifnum = 2,
> .type = QUIRK_MIDI_FIXED_ENDPOINT,
> .data = & (const struct
snd_usb_midi_endpoint_info) {
> .out_cables = 0x0001,
> .in_cables = 0x0001
> }
> },
> {
> .ifnum = -1
> }
> }
> }
> },
>
>
>
> HTH
> Clemens
>
> _________________________________________________________________
> Express yourself instantly with MSN Messenger! Download today it's FREE!
> http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
> _______________________________________________
> Linux-audio-user mailing list
> Linux-audio-user(a)lists.linuxaudio.org
> http://lists.linuxaudio.org/mailman/listinfo/linux-audio-user
>
_________________________________________________________________
Express yourself instantly with MSN Messenger! Download today it's FREE!
http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
31 Jul
31 Jul
6:28 a.m.
New subject: Boss GT-10
It works perfectly with fxfloorboard, except for some details that I
guess that are problems of fxfloorboard itself.
As for the curiosity question, I have no idea. But I'm pretty sure
that Clemens knows it.
Cheers,
Pedro
On Thu, Jul 31, 2008 at 12:32 AM, Tinco Andringa <mail(a)tinco.nl> wrote:
Awesome thanks, that works :D So that only leaves my curiosity question, anyone got a
clue? Is this patch btw on track for inclusion in the driver? I noticed the vendor info
stuff wasn't in it so it doesn't look like a realy driver patch, I added vendor
info in my patch. I will test tomorrow if it works with the floorboard software to see if
it works with the midi stuff too.
Cheers,
Tinco
----------------------------------------
Date: Wed, 30 Jul 2008 23:01:05 +0100
From: ilzogoiby(a)gmail.com
To: mail(a)tinco.nl
Subject: Re: [LAU] Boss GT-10
CC: linux-audio-user(a)lists.linuxaudio.org
Hello,
The "No mixer elems found" error is normal. A for the rest, I guess
you are not correctly selecting the device for recording.
arecord --device=default:CARD=GT10 -t wav -f s16_le -r 44100 -c 2 test.wav
works for me :)
Good luck,
Pedro
On Wed, Jul 30, 2008 at 4:10 PM, Tinco Andringa wrote:
>
> Hello,
>
> I am a bit new to this so please bear with me. I'm trying to get my Boss GT-10 to
work on my (arch) linux install.
>
> I added the patch that was suggested in the post I reply to to my usbquirks.h and
compiled alsa using the guide on this site:
http://www.alsa-project.org/main/index.php/Matrix:Module-usb-audio with as only difference
that I configured with '--with-cards=all'.
>
> After this my BOSS GT-10 was recognised by linux and I am able to play sound over it
using aplay. Recording however seems not to work. When I run arecord -L it shows all three
of my audio cards, including the bossgt, but when I do alsamixer -c 2 it gives the
following error: No mixer elems found. Using a command like arecord -d 5 -t wav test.wav
just gives me the sound recorded by the microphone in another soundcard. It could be that
it's just a matter of using -D to select the right PCM, but I'm not sure how to
find the right PCM.
>
> I suspect this is the reason I cannot record, do you have any idea what goes wrong?
Another question more out of curiosity, why does the patch specify
USB_DEVICE(0x0592,0x00da) whilst the usb device as listed by lsusb has id 0x00db?
>
> If I need supply any specific information
>
> With kind regards and gratitude for the patch,
> Tinco Andringa
>
> --- In reply to: ---
> Clemens Ladisch cladisch at fastmail.net
>
> Thu Jul 24 12:04:48 EDT 2008
>
> edro Ferreira wrote:
>> OK, I've added the output as an attachment :).
>
> Sorry for the delay.
>
> Please try adding the entry below anywhere in sound/usb/usbquirks.h
> and recompile the driver:
>
>
> {
> /* BOSS GT-10 */
> USB_DEVICE(0x0582, 0x00da),
> .driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) {
> .ifnum = QUIRK_ANY_INTERFACE,
> .type = QUIRK_COMPOSITE,
> .data = (const struct snd_usb_audio_quirk[]) {
> {
> .ifnum = 0,
> .type = QUIRK_AUDIO_STANDARD_INTERFACE
> },
> {
> .ifnum = 1,
> .type = QUIRK_AUDIO_STANDARD_INTERFACE
> },
> {
> .ifnum = 2,
> .type = QUIRK_MIDI_FIXED_ENDPOINT,
> .data = & (const struct
snd_usb_midi_endpoint_info) {
> .out_cables = 0x0001,
> .in_cables = 0x0001
> }
> },
> {
> .ifnum = -1
> }
> }
> }
> },
>
>
>
> HTH
> Clemens
>
> _________________________________________________________________
> Express yourself instantly with MSN Messenger! Download today it's FREE!
> http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
> _______________________________________________
> Linux-audio-user mailing list
> Linux-audio-user(a)lists.linuxaudio.org
> http://lists.linuxaudio.org/mailman/listinfo/linux-audio-user
>
_________________________________________________________________
Express yourself instantly with MSN Messenger! Download today it's FREE!
http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
_______________________________________________
Linux-audio-user mailing list
Linux-audio-user(a)lists.linuxaudio.org
http://lists.linuxaudio.org/mailman/listinfo/linux-audio-user
5963
days inactive
5964
days old
linux-audio-user@lists.linuxaudio.org
4 comments
3 participants
participants (3)
-
Clemens Ladisch -
Pedro Ferreira -
Tinco Andringa