24 Nov
2019
24 Nov
'19
8:32 p.m.
Hi.
For years, I used an RME HammerFall under Linux. I love this card, but
I finally goota say goodbye to PCI. What USB/ThunderBolt multichannel
card with mixing/routing capabilities would you recommend? I have been
out of the loop regarding semipro soundcard for many years now, so I
would be happy about some tips that get me started on choosing a device.
I mostly need analog channels. Ideally with a lot of headroom, since I
might be feeding it with quite hot signals (eurorack).
I have heard there are also mixers these days that work as a
multichannel soundcards. Maybe that might be interesting.
However, I will only be using it with linux, so I am really looking for
something that is known to work nicely.
Will be using it with JACK and SuperCollider.
--
CYa,
⡍⠁⠗⠊⠕
24 Nov
24 Nov
9:10 p.m.
Mario Lang <mlang(a)delysid.org> writes:
Hi.
For years, I used an RME HammerFall under Linux. I love this card, but
I finally goota say goodbye to PCI. What USB/ThunderBolt multichannel
card with mixing/routing capabilities would you recommend?
There is the RME Multiface which you likely could use via ThunderBolt to
Expresscard adapter. Whether to bother with something that old is
another question.
I have been out of the loop regarding semipro
soundcard for many years
now, so I would be happy about some tips that get me started on
choosing a device. I mostly need analog channels. Ideally with a lot
of headroom, since I might be feeding it with quite hot signals
(eurorack). I have heard there are also mixers these days that work
as a multichannel soundcards.
Most of the time I use an Onyx 1620 mixer with Firewire card. The
"newer" variants of those mixers have an i after their number (like Onyx
1620i) and come with Firewire built-in (and, except for the largest one,
the 1640i, no longer with balanced recording outputs for separate analog
recording pre-fader). You'd need a Thunderbolt-to-Firewire interface,
of course. I use a built-in Firewire with my T420 but it does not come
standard (I got it for about EUR10 and threw out the landline modem for
that).
The Onyx mixers are nice, but Firewire is not exactly new, and it was
not exactly new when Linux changed to a new Firewire stack so older
Expresscard adapters may actually have buggy support in spite of their
age.
I think I have an Onyx 400F here that is just a mic interface. I
strongly recommend against it in spite of its nicer portability: the DSP
on it tends to die and there are lots of reports of it bricking. Mine
did. No idea whether the comparatively new Linux ALSA software had
something to do with it.
Basically if you go for a Mackie, I'd take one of the mixers rather than
the interface-only things.
RME has more modern interfaces (like the Babyface) but I am not sure
what their actual multichannel offerings are.
Maybe that might be interesting. However, I will only
be using it
with linux, so I am really looking for something that is known to work
nicely. Will be using it with JACK and SuperCollider.
--
David Kastrup
10:30 p.m.
If you are thinking of using the audio interface also as a CV controller,
note that both Motu AVB interfaces and some Presonus interfaces are
DC-coupled and can be used as CV interfaces as well as multi channel units
(at the same time). Other cards might do DC as well-
Very good onboard routing/mixing capabilities on the Motu devices.
Just another 2c take on the subject since Eurorack people might need/want
CV more than other people, I guess
/Anders
Den sön 24 nov. 2019 kl 20:10 skrev David Kastrup <dak(a)gnu.org>rg>:
Mario Lang <mlang(a)delysid.org> writes:
Hi.
For years, I used an RME HammerFall under Linux. I love this card, but
I finally goota say goodbye to PCI. What USB/ThunderBolt multichannel
card with mixing/routing capabilities would you recommend?
There is the RME Multiface which you likely could use via ThunderBolt to
Expresscard adapter. Whether to bother with something that old is
another question.
I have been out of the loop regarding semipro
soundcard for many years
now, so I would be happy about some tips that get me started on
choosing a device. I mostly need analog channels. Ideally with a lot
of headroom, since I might be feeding it with quite hot signals
(eurorack). I have heard there are also mixers these days that work
as a multichannel soundcards.
Most of the time I use an Onyx 1620 mixer with Firewire card. The
"newer" variants of those mixers have an i after their number (like Onyx
1620i) and come with Firewire built-in (and, except for the largest one,
the 1640i, no longer with balanced recording outputs for separate analog
recording pre-fader). You'd need a Thunderbolt-to-Firewire interface,
of course. I use a built-in Firewire with my T420 but it does not come
standard (I got it for about EUR10 and threw out the landline modem for
that).
The Onyx mixers are nice, but Firewire is not exactly new, and it was
not exactly new when Linux changed to a new Firewire stack so older
Expresscard adapters may actually have buggy support in spite of their
age.
I think I have an Onyx 400F here that is just a mic interface. I
strongly recommend against it in spite of its nicer portability: the DSP
on it tends to die and there are lots of reports of it bricking. Mine
did. No idea whether the comparatively new Linux ALSA software had
something to do with it.
Basically if you go for a Mackie, I'd take one of the mixers rather than
the interface-only things.
RME has more modern interfaces (like the Babyface) but I am not sure
what their actual multichannel offerings are.
Maybe that might be interesting. However, I will
only be using it
with linux, so I am really looking for something that is known to work
nicely. Will be using it with JACK and SuperCollider.
--
David Kastrup
_______________________________________________
Linux-audio-user mailing list
Linux-audio-user(a)lists.linuxaudio.org
https://lists.linuxaudio.org/listinfo/linux-audio-user
2239
days inactive
2239
days old
linux-audio-user@lists.linuxaudio.org
2 comments
3 participants
participants (3)
-
Anders Hellquist -
David Kastrup -
Mario Lang