Hello James! Thanks for sharing this piece of music. OK, the singing isn't great, but who am I to complain? :-) Having the drums all in seperate tracks can help you a lot. Even with this rather open and transparent arrangement. May I ramble. This is of course a lot to taste and there are - I'm sure - some quite different basic religious ideas on how to approach this. Mine is more progressive rock or even pop. I will mention some values here, just experiment with the important parameters and find your own. My values are just typical things, that I experienced as useful. Filtering: especially in busy mixes it's nice to filter things as much as possible - and/or - equalise. The hihat are really getting important and audible - through all the rest - around 500 probably even 700 Hertz. So apply a highpass filte4r around that region. A bassdrum doesn't mostly need frequencies up to 22kHz. Depending on your sound something between 1-6kHz might do. those are the really harsh steps, cutting out, what really isn't needed. Then with an EQ lower frequencies, that have to much. I use Fons' 4-band parametric filter (LADSPA unique ID 1970). Take any you like. Activate one band, make it very narrow (offered with most EQs I think) and choose something like 12Db for volume/gain. Then sweep the frequency. I don't know, wire it to the pitchbend wheel of a MIDI keyboard, use the mouse... whatever suits you. If you find an area, which sounds overloud/disagreeable, lower the volume/gain control below 0Db. On typical area of annoyance: around 400-440Hz, especially for chord/rhythm nstruments. A lot happens there and if you have a lot of instruments, a lot adds up to much too much. Note: If auditioned alone tracks can sound slightly flat or at least flatter than the original, test them in the full mix. Compression: Your bassdrum could use some. It sounds rather live, which doesn't fit your song. Use something like the Invada compressor (LADSPA unique 3308 or stereo 3309) or any other compressor you like. Experiment. To cut down the release of the bassdrum, choose longer release time in the compressor. If you want to hear, what the compressor actually really does and what changes, you can start experiments with a very low threshold (-20 to -30Db) and high compression (>10, in a nice GUI the rate could be displayed as 1:something, so 1:10). Then your drumkit might be well disposed with some reverb. Especially on the cymbals and perhaps a little on the hihats. You could add some overall subtle studio room to the kit and then add some more reverb on hihats/cymbals in particular to blend them in more smoothly. For that purpose choose a larger reverb. I could talk a lot about snare drums, but you wouldn't want me to. There's such a lot, that can be done with it. Again EQ (can be more than convenience, also shaping the sound), the same goes for compression and reverb. Everything from super dry 70s to gated 80s or organic 90s prog can be achieved. :-) In my ears, at least the hihats could be taken down a notch or even two. :-) Of course, your vocals should go more upfront normally, at least a little. I could understand, if you rather don't this time. the rhythm guitar might use some EQ'ing as well. It sounds rather bright, gets in the way a little. Perhaps just a different amp/speaker/effect combination on your v-amp. I have noticed before, that sounds, which sound good solo, don't necessarily blend in well in a mix. I once had the time of my life rescuing a nicely played recording with completely the wrong sound. I was there, when it got recorded and chosen. Unfortunately, I didn't have time to go back and change it. It would have been better. Since the result, still isn't, what I'd like. The song underneath all my criticism and I'd rather this and why not that, is nice. Compact, flowing, pleasant. Not completely my stle, but approximating. :-) For a first with your new tool, this is OK. I am looking forward to your next song from this setup. Best wishes Julien ---------------------------------------- http://juliencoder.de/nama/music.html