12 Sep
2005
12 Sep
'05
5:35 a.m.
Bug (?) :
I have a 24 bit stereo track in Ardour connected to Jamin and returned
to another stero track. When the mastering is done I export the mastered
track to 16 bit wav. Everything works, but after Ardour has exported 100%
(and before closing the export screen) it's dead for 15-45 secs.
During this, 'top' shows 85-95% CPU usage for Jamin.
If I close Jamin before exporting, Ardour responds directly.
Question:
I have an Ardour session with 17 tracks that have EQ, compression and
the occasional effect pre-fader, a phaser on a pre-fader send bus and a
stereo reverb pre-fader on the master bus.
If I route the master bus to Jamin and back in on a stereo track
the Jamin output sounds fine, but the stereo track ends up with none of
the effects.
Is it impossible to do a multitrack mastering with the effects intact
or am I doing something wrong?
HW/SW specs: AMD AthlonXP 1200+, 512MB RAM, SB Live!, kernel 2.6.12
rlimits, jack in RT mode. Ardour CVS from Aug 31 and Jamin CVS from
mid/end July.
Regards,
Peder
12 Sep
12 Sep
6 a.m.
Hi Peder,
--- Peder Hedlund <peder(a)musikhuset.org> wrote:
Bug (?) :
I have a 24 bit stereo track in Ardour connected to
Jamin and returned
to another stero track. When the mastering is done I
export the mastered
track to 16 bit wav. Everything works, but after
Ardour has exported 100%
(and before closing the export screen) it's dead for
15-45 secs.
During this, 'top' shows 85-95% CPU usage for Jamin.
If I close Jamin before exporting, Ardour responds
directly.
I see this too. Until someone fixes it, just let it
run it's course.
Question:
I have an Ardour session with 17 tracks that have
EQ, compression and
the occasional effect pre-fader, a phaser on a
pre-fader send bus and a
stereo reverb pre-fader on the master bus.
If I route the master bus to Jamin and back in on a
stereo track
the Jamin output sounds fine, but the stereo track
ends up with none of
the effects.
Is it impossible to do a multitrack mastering with
the effects intact
or am I doing something wrong?
Ardour; Options, Miscelaneous, Run Plugins While
Recording.
There was a point when I thought this was a bug. I
installed Timemachine and started recording mixes into
it. dah!
ron
HW/SW specs: AMD AthlonXP 1200+, 512MB RAM, SB
Live!, kernel 2.6.12
rlimits, jack in RT mode. Ardour CVS from Aug 31 and
Jamin CVS from
mid/end July.
Regards,
Peder
______________________________________________________
Yahoo! for Good
Watch the Hurricane Katrina Shelter From The Storm concert
http://advision.webevents.yahoo.com/shelter
7:13 a.m.
HI
I'll try and answer this.
Your piping the master out of the source track complete with all effects
to Jamin (try hearing just the master outs, are the effects on there
yes/no?)
You need to be sure what your monitoring, ie: are you hearing the right
outputs?
I normaly run jamin outputs to 2 extra inputs on my mixer to be sure
that what I hear is what is going to disk.
Jamin will allow you to output to multiple outputs, you must hear what
the new tracks are 'hearing'
Ok so you have:
Ardour:
tk 1 source music Left
tk 2 " " Right
These two tracks have effects on them going to master out (on the master
outs)
Are you running these two tracks into jamin and bypassing the master?
Make sure your hearing the final mix and not just the source through Jamin.
Hope this helps.
Cheers
Bob
Peder Hedlund wrote:
Bug (?) :
I have a 24 bit stereo track in Ardour connected to Jamin and returned
to another stero track. When the mastering is done I export the mastered
track to 16 bit wav. Everything works, but after Ardour has exported 100%
(and before closing the export screen) it's dead for 15-45 secs.
During this, 'top' shows 85-95% CPU usage for Jamin.
If I close Jamin before exporting, Ardour responds directly.
Question:
I have an Ardour session with 17 tracks that have EQ, compression and
the occasional effect pre-fader, a phaser on a pre-fader send bus and a
stereo reverb pre-fader on the master bus.
If I route the master bus to Jamin and back in on a stereo track
the Jamin output sounds fine, but the stereo track ends up with none of
the effects.
Is it impossible to do a multitrack mastering with the effects intact
or am I doing something wrong?
HW/SW specs: AMD AthlonXP 1200+, 512MB RAM, SB Live!, kernel 2.6.12
rlimits, jack in RT mode. Ardour CVS from Aug 31 and Jamin CVS from
mid/end July.
Regards,
Peder
Bearmusic
hearmymusic.co.uk <http:www.hearmymusic.co.uk>
6:31 p.m.
I've had this problem and found that it is usually because plugins or
connected programs are still sending audio data. Ardour will keep
exporting as long as anything in the pipeline is producing output.
The problem went away for me when I turned on the "Stop plugins with
transport" option. That way when the export hit's the end marker and
the transport is consequentially stopped, the plugin's output is
stopped as well.
-Reuben
On 9/12/05, Peder Hedlund <peder(a)musikhuset.org> wrote:
Bug (?) :
I have a 24 bit stereo track in Ardour connected to Jamin and returned
to another stero track. When the mastering is done I export the mastered
track to 16 bit wav. Everything works, but after Ardour has exported 100%
(and before closing the export screen) it's dead for 15-45 secs.
During this, 'top' shows 85-95% CPU usage for Jamin.
If I close Jamin before exporting, Ardour responds directly.
Question:
I have an Ardour session with 17 tracks that have EQ, compression and
the occasional effect pre-fader, a phaser on a pre-fader send bus and a
stereo reverb pre-fader on the master bus.
If I route the master bus to Jamin and back in on a stereo track
the Jamin output sounds fine, but the stereo track ends up with none of
the effects.
Is it impossible to do a multitrack mastering with the effects intact
or am I doing something wrong?
HW/SW specs: AMD AthlonXP 1200+, 512MB RAM, SB Live!, kernel 2.6.12
rlimits, jack in RT mode. Ardour CVS from Aug 31 and Jamin CVS from
mid/end July.
Regards,
Peder
7016
days inactive
7016
days old
linux-audio-user@lists.linuxaudio.org
3 comments
4 participants
participants (4)
-
Peder Hedlund -
R Parker -
Reuben Martin -
studio-64