The sound card is a SBLive. Sorry. El Jue 21 Oct 2004 06:59, Steve Harris escribió:

Hi Mark! Thank you very much for your answer. I'll try to explain the situation. With some friends we're going to record a simple live performance. We don't have multiple channel sound cards, so we plan to use several sound cards ( Digidesign AUDIOMEDIA 3 and Sound Blaster Live). As there are no GNU/Linux drivers for the AUDIOMEDIA we're forced to use a Window$ system with it, and a GNU/Linux system with the SBLive. We plan to record in the Session software recieving the SBlive through the SPDIF port (you can tell Session to syncronise to the SPDIF input). That's why we need to use SPDIF in GNU/Linux. You say there's no difference in using an audio port or using SPDIF (in a SBLive), but SPDIF port is not present in qjack. May be I'm terribly wrong, but the qjack ports I have are: readable clients / output ports : alsapcm capture 1 y 2 writeable clients / input ports : alsapcm playback 1 y 2 ¿How can I send the speakers to the SPDIF? It would be great if you could explain how to syncronise diferent systems through the SPDIF in GNU/Linux. Thanks a lot! Martín. El Jue 21 Oct 2004 15:04, Mark Knecht escribió:

Hi Mark. Thanks again for your kind answer. The complicated hardware picture is due to our interest in using GNU/Linux. The problem is the Audio Media III can't work in GNU/Linux. So we planned a more complicated configuration using two OS. To simplify, we finally decided to use both cards in the same computer running Window$ and KxDrive. The AM III can sync to an external SPDIF signal. So we use the SBLive as a clock master, sending its analog inputs trough the SPDIF output (using KxDrive). The AM III recieves the SPDIF Input and 2 Analog Input. In this way we can record four independient audio signals using the Session software. The analog signals are constantly drifted 7 samples. This can be fixed manually. Signal 1 -> SBLive OUT SPDIF L -> AM III IN SPDIF L -> Session CH1 Signal 2 -> SBLive OUT SPDIF R-> AM III IN SPDIF R -> Session CH2 Signal 3 ---------------------------------> AM III IN Analog L -> Session CH3 Signal 4 ---------------------------------> AM III IN Analog R -> Session CH4 However, It's a pitty we couldn't use GNU/Linux as we planned!!. Thanks for the information about the ALSA SPDIF support for the SBLive. It isn't working yet, but we're going to study it carefully. And thanks for the tip to sync RME cards. We plan to get pro cards in the near future to use under GNU/Linux. Regards, Martín. ----- Original Message ----- From: "Mark Knecht" <markknecht(a)gmail.com> To: "Martin Rocamora" <mrocamora(a)adinet.com.uy> Cc: "A list for linux audio users" <linux-audio-user(a)music.columbia.edu> Sent: Thursday, October 21, 2004 7:17 PM Subject: Re: [linux-audio-user] SPDIF - jack or ecasound On Thu, 21 Oct 2004 19:45:10 -0300, Martin Rocamora <mrocamora(a)adinet.com.uy> wrote: don't and software GNU/Linux. OK, this sounds *very* complicated to me. I understand the motivation, but I still don't see the eact hardware picture in my mind. You might have to draw a better picture. We can decide that later. Firs a few questions and points: 1) You say you are going to use multiple sound cards. Are you thinking these will be in the same computer? Or in separate computers? 2) Jack will not work, TTBOMK, with multiple sound cards. It will work with something called a virtual sound card which can be created (somehow, with help from Clemens and Jaroslav) input .asoundrc file. That is beyond me. However, it will only work if the cards can be reliably synced with each other. 3) The bad news - I think - is that these two sound cards probably cannot be synced to each other. They both have onboard hard wired crystal oscillators I believe. To sync a card it must accept a clock from an outside source. I'm pretty sure that the Audiomedia cannot do this. I doubt the SB can either. These are just guesses, but normally low end sound cards do not support external clock sources. On the other hand, if the two cards were in *separate* computers then you could, in theory, record separate streams in each machine. this would work, but unfortunately, since the two cards are running on differnet crystals, the streams are going to be drifting from each other. To sync them back together you'd have to resample one or both which is going to cause degradation of the digital signal. Over all, and I hate to say this, I think you'd be better off to use an inexpensive external mixer and then record a single stereo stream. wrong, Humm...possibly the Alsa driver doesn't support spdif on this card? I did spend some time looking at the Alsa page for the SB Live and ran across an entry that points here: http://alsa.opensrc.org/index.php?page=SurroundSound Typically spdif on these cards is used to output 5.1 type audio from a DVD. Possibly you can get some clues from this page? On the other hand, you haven't said whether this is Optical spdif which (I think) is only 2 channel) When I said that 'spdif is no different...' I may have spoken a bit fast. On my cards the spdif ports are supported in the main driver and the spdif ports jsut show up in QJC like any other port. I send data there, or receive data from there, exactly like other ports. I suspect that when you do get it working that Jack and WJC will treat it like any other port. Be forewarned. On many lower end cards, if you are going to use spdif you have to run at 48K. If you started Jack at 44.1K that port might not show up, or might show up but you will be doing resampling either in software or hardware. It's messy. You would need an external D/A, such as an Apogee: http://www.apogeedigital.com/support/documents.php?show=minidac The input would be your spdif output. The D/A output would go to an amp and then on to the speakers. This is typical of mid to high end recording studios. You can do the same thing with ADAT or other digital interfaces. (I use ADAT mostly.) It's completely beyond 'Alsa' and dependant on other applications. WIth the RME cards there is a support app called hdspconf which tells the card where to get their clock. I can sync to any ADAT input, any spdif input, Word Clock, or an internal crystal. Alsa doesn't know I'm doing it. I sync Windows/Pro Tools and Gentoo/RME systems together using these interfaces, but as I say, it's completely beyond Alsa. Well, I hope I've helped. I'm not sure there's much positive info up there. --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.783 / Virus Database: 529 - Release Date: 25/10/04