9 Jan
2009
9 Jan
'09
2:04 a.m.
Does the Edirol UA-101 play audio sent to it via USB? Can you monitor
(phones) the usb audio? And does it record audio? Do you have to
reboot the when switching between recording and playing?
The UA-25EX that I just purchased does not do allow monitoring of usb
input, and when using the mode 96kHz you have to reboot the device when
switching from recording to playing. Both of these are serious down
sides to the use I had in mind for the device.
/Allan
--
Allan Wind
Life Integrity, LLC
http://lifeintegrity.com
9 Jan
9 Jan
4:39 a.m.
On Fri, 9 Jan 2009 01:04:31 -0500
Allan Wind <allan_wind(a)lifeintegrity.com> wrote:
Does the Edirol UA-101 play audio sent to it via USB?
Can you
monitor (phones) the usb audio? And does it record audio? Do you
have to reboot the when switching between recording and playing?
The UA-25EX that I just purchased does not do allow monitoring of usb
input, and when using the mode 96kHz you have to reboot the device
when switching from recording to playing. Both of these are serious
down sides to the use I had in mind for the device.
/Allan
What do you mean by 'monitoring of usb input'?
You're talking about rebooting, but all one needs to do with my UA25
(no EX) is unplug the device, change the samplerate and re-plug it. I
imagine that it can be annoying when you need to change the samplerate
often.
1:21 p.m.
On 2009-01-09T09:39:44, hollunder(a)gmx.at wrote:
What do you mean by 'monitoring of usb input'?
With the UA25EX input 1 + 2 is routed to phone + output 1 + 2, while the
audio stream sent to the device via the usb port is only sent to output
1 + 2 and NOT phone.
You're talking about rebooting, but all one needs
to do with my UA25
(no EX) is unplug the device, change the samplerate and re-plug it. I
imagine that it can be annoying when you need to change the samplerate
often.
With the UA25EX also have to unplug the device when switching between
recording (96R) and playback (96P) when using the 96kHz sample rate
along these lines:
1. switch to 96R
2. bounce the device by unplugging and plugging usb cable
4. record
5. switch to 96P
6. bounce device
7. play
It works like yours, no unplugging required, with 44.1kHz and 48kHz
sample rates.
/Allan
--
Allan Wind
Life Integrity, LLC
http://lifeintegrity.com
5:04 p.m.
On Fri, 9 Jan 2009 12:21:41 -0500
Allan Wind <allan_wind(a)lifeintegrity.com> wrote:
Yes, the 96kHz case probably is annoying but never was and probably
never will be relevant to me since I doubt that it makes sense anyway
except for special applications. One probably needs special microphones
to get somewhere near this frequency, same is probably true for
speakers, and I don't know of any non-scientific reason for doing
something like this in the first place.
Philipp
On 2009-01-09T09:39:44, hollunder(a)gmx.at wrote:
This seems odd to me. For me the output case (for example playback of
some previously recorded audio) is that audio goes to Phones and
probably to jack outputs, chinch output, s/pdiff out. Phones output
definitely works here, in fact I haven't used any other form of output
yet.
What do you mean by 'monitoring of usb
input'?
With the UA25EX input 1 + 2 is routed to phone + output 1 + 2, while
the audio stream sent to the device via the usb port is only sent to
output 1 + 2 and NOT phone. You're
talking about rebooting, but all one needs to do with my UA25
(no EX) is unplug the device, change the samplerate and re-plug it.
I imagine that it can be annoying when you need to change the
samplerate often.
With the UA25EX also have to unplug the device when switching between
recording (96R) and playback (96P) when using the 96kHz sample rate
along these lines:
1. switch to 96R
2. bounce the device by unplugging and plugging usb cable
4. record
5. switch to 96P
6. bounce device
7. play
It works like yours, no unplugging required, with 44.1kHz and 48kHz
sample rates.
/Allan
18 Jan
18 Jan
2:13 p.m.
New subject: UA25EX (was: Edirol UA-101: does the following work?(
On 2009-01-09T12:21:41, Allan Wind wrote:
On 2009-01-09T09:39:44, hollunder(a)gmx.at wrote:
I was not able to get any output on the phones port via either input 1
or 2 or USB. Roland seemed to think the device was defective, so
returned the device and will probably pick up a TAPCO Link.USB instead.
/Allan
--
Allan Wind
Life Integrity, LLC
http://lifeintegrity.com
What do you mean by 'monitoring of usb
input'?
With the UA25EX input 1 + 2 is routed to phone + output 1 + 2, while the
audio stream sent to the device via the usb port is only sent to output
1 + 2 and NOT phone.
5836
days inactive
5845
days old
linux-audio-user@lists.linuxaudio.org
4 comments
2 participants
participants (2)
-
Allan Wind -
hollunder＠gmx.at