6 Jan
2006
6 Jan
'06
12:22 a.m.
Tim Howard wrote:
cmetzler wrote:
I have loaded the same soundfont that I use under Windoze, and all the
instruments show up in Rosegarden... But still no sound.
Hrm. You've tried other programs to send the MIDI sequence to the
synth (e.g. aplaymidi), right? (just to make sure that it's not
an issue with Rosegarden) Alternately, you've successfully played
the MIDI sequence through a softsynth like timidity, right? (to
point the finger directly at getting the synth working) I think
I remember reading that you'd done so. Right?
If so, I'm at a bit of a loss. I never had any problem getting
this stuff to work. Once upon a time, about a year and a half ago,
I wrote up a brief HOWTO-ish document for MIDI on Linux, but it's
currently on a disk attached to a machine that won't boot. The
only other thing I can think of right now: I believe I remember
reading that you'd played around with all the controls in
alsamixer that seemed relevant; you may want to revisit that
again. I haven't seen how the emu10k1 looks in recent versions of
alsa/alsamixer, but the volume control for the output of the
wavetable synth used to have the singularly unhelpful title of
"Music" in alsamixer. You might play around there. Or perhaps
steal the mixer settings from someone who's got it working, and
see if that helps.
I'm having exactly the same problem with my emu10k1 (SBLive 5.1)
sound card. All the MIDI programs I try seem to _think_ they're
working... but still no sound! (Other audio works fine, though.) I
have used the SuSE and Fedora distros, but same thing.
Any other ideas?
Just to verify: you loaded a valid soundfont into the wavetable synth,
and you're sure you're sending the MIDI command sequence to the wavetable
synth? It's
probably something ridiculously simple, since I'm new to this...
S'ok. You're right that it usually is something simple, but it
never seems that way until *after* the problem is solved, when
it's easy to call it that!
-c
6 Jan
6 Jan
8:49 a.m.
New subject: [linux-audio-user] Debian 2.6.14 alsa problems
>>>> "c" == cmetzler
<cmetzler(a)speakeasy.net> writes:
c> I haven't seen how the emu10k1 looks in recent versions of
c> alsa/alsamixer, but the volume control for the output of the
c> wavetable synth used to have the singularly unhelpful title of
c> "Music" in alsamixer.
It looks to me like that has now been replaced with "synth".
c> You might play around there. Or perhaps steal the mixer
c> settings from someone who's got it working, and see if that
c> helps.
This sounds like a good idea. Can someone using the emu10k1 driver
with working MIDI post their mixer settings?
--
Laura (mailto:lconrad@laymusic.org , http://www.laymusic.org/ )
(617) 661-8097 fax: (501) 641-5011
233 Broadway, Cambridge, MA 02139
10:59 a.m.
New subject: [linux-audio-user] Debian 2.6.14 alsa problems
On Friday 06 January 2006 13:48, Laura Conrad wrote:
Hi Laura On Debian Sarge/Etch, using Alsamixer v1.0.10 , the only controls
affecting midi output are. Master; Front; and Music; obviously with the
Audigy switch unmuted also.
I'm using Kmid, and Emu10k1 Wavetable Emu10k1 Port2 -ALSA device (shown in
Kmids midi config), and the other 3 ports are ok.
Sfxload autoloads the soundfont on KDE startup.
Souncard is: Audigy2 soundblaster (emu10k1). Chip: Sigmatel STAC9721/23
Kernel: 2.6.11-1-386
Alsa version: 1.0.8 (with the 2.6.11 kernel)
Alsa components installed:
alsa-base 1.0.10-3
alsa-modules-2.4-27-2-386 1.0.10+1 (I have a 2.4 kernel, as well as the
2.6)
alsa-oss 1.0.10-1
alsa-utils 1.0.10-1
All the best. Nigel.
ps: sorry messing with the BIOS didn't fix it.
>>>> "c" == cmetzler <cmetzler(a)speakeasy.net> writes:
c> I haven't seen how the emu10k1 looks in recent versions of
c> alsa/alsamixer, but the volume control for the output of the
c> wavetable synth used to have the singularly unhelpful title of
c> "Music" in alsamixer.
It looks to me like that has now been replaced with "synth".
c> You might play around there. Or perhaps steal the mixer
c> settings from someone who's got it working, and see if that
c> helps.
This sounds like a good idea. Can someone using the emu10k1 driver
with working MIDI post their mixer settings?
11:42 a.m.
New subject: [linux-audio-user] Debian 2.6.14 alsa problems
>>>> "NH" == Nigel Henry
<cave.dnb(a)tiscali.fr> writes:
NH> Hi Laura On Debian Sarge/Etch, using Alsamixer v1.0.10 , the only controls
NH> affecting midi output are. Master; Front; and Music; obviously with the
NH> Audigy switch unmuted also.
For the SBLive, 1.0.10 doesn't seem to have either Front or Music.
I'm pretty sure Music is now Synth; does anyone know what Front turned
into?
NH> I'm using Kmid, and Emu10k1 Wavetable Emu10k1 Port2 -ALSA device (shown in
NH> Kmids midi config), and the other 3 ports are ok.
Kmid looks like it would be really nice, if it would only play the
sound.
NH> Souncard is: Audigy2 soundblaster (emu10k1). Chip: Sigmatel
NH> STAC9721/23
Card: SBLive! Platinum [CT4760P]
Chip: TriTech TR28602
NH> Kernel: 2.6.11-1-386
Kernel: 2.6.14-2-386
NH> Alsa version: 1.0.8 (with the 2.6.11 kernel)
[~]# cat /proc/asound/version
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12 08:13:09 2005
UTC).
NH> Alsa components installed:
NH> alsa-base 1.0.10-3
NH> alsa-modules-2.4-27-2-386 1.0.10+1 (I have a 2.4 kernel, as well as the
NH> 2.6)
NH> alsa-oss 1.0.10-1
NH> alsa-utils 1.0.10-1
[~]# dpkg -l alsa-modules-2*
||/ Name Version Description
+++-===========================-===========================-======================================================================
ii alsa-base 1.0.10-3 ALSA driver configuration
files
ii alsa-modules-2.4.27-1-686 1.0.6a+4 Advanced Linux Sound
Architecture (drivers)
ii alsa-oss 1.0.10-1 ALSA wrapper for OSS
applications
ii alsa-utils 1.0.10-1 ALSA utilities
ii alsaplayer 0.99.76-0.2 PCM player designed for ALSA
ii alsaplayer-common 0.99.76-0.2 PCM player designed for ALSA
(common files)
ii alsaplayer-gtk 0.99.76-0.2 PCM player designed for ALSA
(GTK version)
ii alsaplayer-oss 0.99.76-0.2 PCM player designed for ALSA
(OSS output module)
NH> ps: sorry messing with the BIOS didn't fix it.
No problem. If I'm not profusely thanking people for trying to help
with every message, it isn't because I'm not grateful.
--
Laura (mailto:lconrad@laymusic.org , http://www.laymusic.org/ )
(617) 661-8097 fax: (501) 641-5011
233 Broadway, Cambridge, MA 02139
1:13 p.m.
New subject: [linux-audio-user] Debian 2.6.14 alsa problems
On Friday 06 January 2006 16:42, Laura Conrad wrote:
Hi Laura. Lee Revell posted a reply to someone else on this thread. You may
have missed it. He says to make sure that "Synth" volume is up, so I think
that's saying that with the "Live" card, "Synth" equates with
"Music" on my
Audigy2.
Also he asked for the output of:
cat /proc/asound/card0/wavetableD1
Would you post the output of this please, as it will confirm if the soundfont
is loaded.
I also compared your lsmod with mine, and there are only minor differences.
Mine has snd-usb-audio, for the sake of my USB midi keyboard. Yours has
snd-rtctimer, and snd-mpu401-uart, which mine doesn't. Not sure of what
snd-rtctimer is for , but as I don't have realtime in this kernel, it may be
something to do with that.
This is a real Nancy Drew & the Hardy Boys mystery. Nigel.
>>>> "NH" == Nigel Henry <cave.dnb(a)tiscali.fr> writes:
NH> Hi Laura On Debian Sarge/Etch, using Alsamixer v1.0.10 , the only
controls NH> affecting midi output are. Master; Front; and Music; obviously
with the NH> Audigy switch unmuted also.
For the SBLive, 1.0.10 doesn't seem to have either Front or Music.
I'm pretty sure Music is now Synth; does anyone know what Front turned
into?
NH> I'm using Kmid, and Emu10k1 Wavetable Emu10k1 Port2 -ALSA device
(shown in NH> Kmids midi config), and the other 3 ports are ok.
Kmid looks like it would be really nice, if it would only play the
sound.
NH> Souncard is: Audigy2 soundblaster (emu10k1). Chip: Sigmatel
NH> STAC9721/23
Card: SBLive! Platinum [CT4760P]
Chip: TriTech TR28602
NH> Kernel: 2.6.11-1-386
Kernel: 2.6.14-2-386
NH> Alsa version: 1.0.8 (with the 2.6.11 kernel)
[~]# cat /proc/asound/version
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12
08:13:09 2005 UTC).
NH> Alsa components installed:
NH> alsa-base 1.0.10-3
NH> alsa-modules-2.4-27-2-386 1.0.10+1 (I have a 2.4 kernel, as
well as the NH> 2.6)
NH> alsa-oss 1.0.10-1
NH> alsa-utils 1.0.10-1
[~]# dpkg -l alsa-modules-2*
||/ Name Version Description
+++-===========================-===========================-===============
======================================================= ii alsa-base
1.0.10-3 ALSA driver configuration files ii
alsa-modules-2.4.27-1-686 1.0.6a+4 Advanced Linux
Sound Architecture (drivers) ii alsa-oss 1.0.10-1
ALSA wrapper for OSS applications ii alsa-utils
1.0.10-1 ALSA utilities ii alsaplayer
0.99.76-0.2 PCM player designed for ALSA ii
alsaplayer-common 0.99.76-0.2 PCM player designed
for ALSA (common files) ii alsaplayer-gtk 0.99.76-0.2
PCM player designed for ALSA (GTK version) ii alsaplayer-oss
0.99.76-0.2 PCM player designed for ALSA (OSS output
module)
NH> ps: sorry messing with the BIOS didn't fix it.
No problem. If I'm not profusely thanking people for trying to help
with every message, it isn't because I'm not grateful.
1:22 p.m.
New subject: [linux-audio-user] Debian 2.6.14 alsa problems
>>>> "NH" == Nigel Henry
<cave.dnb(a)tiscali.fr> writes:
NH> Hi Laura. Lee Revell posted a reply to someone else on this thread. You may
NH> have missed it. He says to make sure that "Synth" volume is up, so I
think
NH> that's saying that with the "Live" card, "Synth"
equates with "Music" on my
NH> Audigy2.
Yes, I got that. That's one of the things I'd already upped.
NH> Also he asked for the output of:
NH> cat /proc/asound/card0/wavetableD1
NH> Would you post the output of this please, as it will confirm
NH> if the soundfont is loaded.
[~]# cat /proc/asound/card0/wavetableD1
Device: Emu10k1
Ports: 4
Addresses: 65:0 65:1 65:2 65:3
Use Counter: 0
Max Voices: 64
Allocated Voices: 0
Memory Size: 134217728
Memory Available: 130711440
Allocated Blocks: 458
SoundFonts: 1
Instruments: 1789
Samples: 456
Locked Instruments: 1789
Locked Samples: 456
You have mail in /var/spool/mail/lconrad
[~]#
Could the fact that all the samples are locked be relevant? How would
I unlock them?
--
Laura (mailto:lconrad@laymusic.org , http://www.laymusic.org/ )
(617) 661-8097 fax: (501) 641-5011
233 Broadway, Cambridge, MA 02139
1:50 p.m.
New subject: [linux-audio-user] Debian 2.6.14 alsa problems
On Friday 06 January 2006 18:22, Laura Conrad wrote:
No. Thats just fine as it is, apart from you only having half the number of
instruments that I have, but at least confirms that the soundfont is loaded.
If no soundfont was loaded, the first 8 lines would be the same. The line:
Allocated Blocks: would show "1" , and all the rest of the lines would show
"0" .
The soundfont I have loaded is the one from the Creative CDROM. It is
CT4MGM.SF2, and shows "Instruments: 3560" when loaded .
Are there any larger soundfonts on your Creative CDROM? I've no idea, but
perhaps the soundfont is not large enough to play the midi file that you are
trying.
If you do use KDE. Try Kmid, which even though it crashes now and again, at
least I know it plays midi files ok. Nigel.
>>>> "NH" == Nigel Henry <cave.dnb(a)tiscali.fr> writes:
NH> Hi Laura. Lee Revell posted a reply to someone else on this thread.
You may NH> have missed it. He says to make sure that "Synth" volume is up,
so I think NH> that's saying that with the "Live" card,
"Synth" equates
with "Music" on my NH> Audigy2.
Yes, I got that. That's one of the things I'd already upped.
NH> Also he asked for the output of:
NH> cat /proc/asound/card0/wavetableD1
NH> Would you post the output of this please, as it will confirm
NH> if the soundfont is loaded.
[~]# cat /proc/asound/card0/wavetableD1
Device: Emu10k1
Ports: 4
Addresses: 65:0 65:1 65:2 65:3
Use Counter: 0
Max Voices: 64
Allocated Voices: 0
Memory Size: 134217728
Memory Available: 130711440
Allocated Blocks: 458
SoundFonts: 1
Instruments: 1789
Samples: 456
Locked Instruments: 1789
Locked Samples: 456
You have mail in /var/spool/mail/lconrad
[~]#
Could the fact that all the samples are locked be relevant? How would
I unlock them?
7 Jan
7 Jan
10:34 a.m.
New subject: [linux-audio-user] Debian 2.6.14 alsa problems
>>>> "NH" == Nigel Henry
<cave.dnb(a)tiscali.fr> writes:
NH> Also he asked for the output of:
NH> cat /proc/asound/card0/wavetableD1
>
NH> Would you post the output of
this please, as it will confirm
NH> if the soundfont is loaded.
>
>> [~]# cat
/proc/asound/card0/wavetableD1
>> Device: Emu10k1
>> Ports: 4
>> Addresses: 65:0 65:1 65:2 65:3
>> Use Counter: 0
>> Max Voices: 64
>> Allocated Voices: 0
>> Memory Size: 134217728
>> Memory Available: 130711440
>> Allocated Blocks: 458
>> SoundFonts: 1
>> Instruments: 1789
>> Samples: 456
>> Locked Instruments: 1789
>> Locked Samples: 456
>> You have mail in /var/spool/mail/lconrad
>> [~]#
>
NH> Are there any larger soundfonts on your Creative CDROM? I've no idea, but
NH> perhaps the soundfont is not large enough to play the midi file that you are
NH> trying.
This font is the one that's worked in the past when I've had MIDI
working. I do have others.
I just loaded the one with the largest file size, 4GMGSMT.SF2, and it
looks more like yours, but still doesn't make noise when I play MIDI:
[~]# cat /proc/asound/card0/wavetableD1
Device: Emu10k1
Ports: 4
Addresses: 65:0 65:1 65:2 65:3
Use Counter: 0
Max Voices: 64
Allocated Voices: 0
Memory Size: 134217728
Memory Available: 130183486
Allocated Blocks: 490
SoundFonts: 1
Instruments: 3560
Samples: 488
Locked Instruments: 3560
Locked Samples: 488
NH> If you do use KDE. Try Kmid, which even though it crashes now and again, at
NH> least I know it plays midi files ok. Nigel.
It seems to do the same thing as the command line players -- look like
it's playing, but not produce any sound.
--
Laura (mailto:lconrad@laymusic.org , http://www.laymusic.org/ )
(617) 661-8097 fax: (501) 641-5011
233 Broadway, Cambridge, MA 02139
8:11 p.m.
New subject: [linux-audio-user] Debian 2.6.14 alsa problems
On Saturday 07 January 2006 15:34, Laura Conrad wrote:
Hi Laura. Sorry for the delay in replying. You said on an earlier post that
you'd had midi working. Was this on the same machine, and if so, which
distro?
I'm fast running out of suggestions. If the audio is working ok, TiMidity
plays midi files ok, the only other things you should need for playing midi,
for instance with Kmid are. Make sure that snd-emu10k1-synth is loaded. Load
the soundfont onto the card, and if using KMid. Make sure that in Kmids
"Settings", "Midi Setup", that you select one of the wavetable ports,
and ok
it. Then the midi file should just play after loading it in Kmid.
The only thing I don't quite understand, if I read this correctly, is that
Qjackctl shows both sound cards as "hw:0
Lets try setting the cards to load as card 1, and card2. This I've had to do
so that snd-usb-audio loads as the second card, otherwise Alsa detects my usb
midi keyboard as the soundcard.
Open the CLI and su to root, then open a text editor, Kwrite, Gedit or
something. Go to. /etc/modutils/sound . This is possibly a blank page. Add
these lines.
alias snd-card-0 snd-emu10k1
options snd-emu10k1 index=0
alias snd-card-1 snd-via82xx
options snd-via82xx index=1
Save, then close the editor. Then run "update-modules" without the double
quotes, which will update /etc/modules.conf .
It may now be worth looking in Qjackctl's settings to see if you now have
hw:0 , and hw:1 . If not it may be worth rebooting the machine, making sure
that snd-emu10k1-synth, and the soundfont is loaded. Look in Qjackctl again,
to check whether you have 2 entries in the settings/interface. Then go for a
midi file again in Kmid, again checking that settings/midi-setup shows a
wavetable port selected.
My wrist is getting a bit tired now, like the Simpsons line about doing
animation in realtime.
Even if this don't work, you are working yourself around different bits of the
machine. I'm not being flippant, just trying to remain positive. Nigel.
>>>> "NH" == Nigel Henry <cave.dnb(a)tiscali.fr> writes:
NH> Also he asked for the output of:
NH> cat /proc/asound/card0/wavetableD1
NH> Would you post the output of this please, as it will confirm
NH> if the soundfont is loaded.
> [~]# cat /proc/asound/card0/wavetableD1
> Device: Emu10k1
> Ports: 4
> Addresses: 65:0 65:1 65:2 65:3
> Use Counter: 0
> Max Voices: 64
> Allocated Voices: 0
> Memory Size: 134217728
> Memory Available: 130711440
> Allocated Blocks: 458
> SoundFonts: 1
> Instruments: 1789
> Samples: 456
> Locked Instruments: 1789
> Locked Samples: 456
> You have mail in /var/spool/mail/lconrad
> [~]#
NH> Are there any larger soundfonts on your Creative CDROM? I've no
idea, but NH> perhaps the soundfont is not large enough to play the midi
file that you are NH> trying.
This font is the one that's worked in the past when I've had MIDI
working. I do have others.
I just loaded the one with the largest file size, 4GMGSMT.SF2, and it
looks more like yours, but still doesn't make noise when I play MIDI:
[~]# cat /proc/asound/card0/wavetableD1
Device: Emu10k1
Ports: 4
Addresses: 65:0 65:1 65:2 65:3
Use Counter: 0
Max Voices: 64
Allocated Voices: 0
Memory Size: 134217728
Memory Available: 130183486
Allocated Blocks: 490
SoundFonts: 1
Instruments: 3560
Samples: 488
Locked Instruments: 3560
Locked Samples: 488
NH> If you do use KDE. Try Kmid, which even though it crashes now and
again, at NH> least I know it plays midi files ok. Nigel.
It seems to do the same thing as the command line players -- look like
it's playing, but not produce any sound. 
6 Jan
6 Jan
2:54 p.m.
New subject: [linux-audio-user] Debian 2.6.14 alsa problems
On Fri, 2006-01-06 at 18:13 +0100, Nigel Henry wrote:
On Friday 06 January 2006 16:42, Laura Conrad wrote:
Hi Laura. Lee Revell posted a reply to someone else on this thread. You may
have missed it. He says to make sure that "Synth" volume is up, so I think
that's saying that with the "Live" card, "Synth" equates with
"Music" on my
Audigy2.
The control is now called Synth. If it's called Music on your system it
means you have an ancient ALSA version and shopuld upgrade.
Lee
>>>> "NH" == Nigel Henry <cave.dnb(a)tiscali.fr> writes:
NH> Hi Laura On Debian Sarge/Etch, using Alsamixer v1.0.10 , the only
controls NH> affecting midi output are. Master; Front; and Music; obviously
with the NH> Audigy switch unmuted also.
For the SBLive, 1.0.10 doesn't seem to have either Front or Music.
I'm pretty sure Music is now Synth; does anyone know what Front turned
into?
NH> I'm using Kmid, and Emu10k1 Wavetable Emu10k1 Port2 -ALSA device
(shown in NH> Kmids midi config), and the other 3 ports are ok.
Kmid looks like it would be really nice, if it would only play the
sound.
NH> Souncard is: Audigy2 soundblaster (emu10k1). Chip: Sigmatel
NH> STAC9721/23
Card: SBLive! Platinum [CT4760P]
Chip: TriTech TR28602
NH> Kernel: 2.6.11-1-386
Kernel: 2.6.14-2-386
NH> Alsa version: 1.0.8 (with the 2.6.11 kernel)
[~]# cat /proc/asound/version
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12
08:13:09 2005 UTC).
NH> Alsa components installed:
NH> alsa-base 1.0.10-3
NH> alsa-modules-2.4-27-2-386 1.0.10+1 (I have a 2.4 kernel, as
well as the NH> 2.6)
NH> alsa-oss 1.0.10-1
NH> alsa-utils 1.0.10-1
[~]# dpkg -l alsa-modules-2*
||/ Name Version Description
+++-===========================-===========================-===============
======================================================= ii alsa-base
1.0.10-3 ALSA driver configuration files ii
alsa-modules-2.4.27-1-686 1.0.6a+4 Advanced Linux
Sound Architecture (drivers) ii alsa-oss 1.0.10-1
ALSA wrapper for OSS applications ii alsa-utils
1.0.10-1 ALSA utilities ii alsaplayer
0.99.76-0.2 PCM player designed for ALSA ii
alsaplayer-common 0.99.76-0.2 PCM player designed
for ALSA (common files) ii alsaplayer-gtk 0.99.76-0.2
PCM player designed for ALSA (GTK version) ii alsaplayer-oss
0.99.76-0.2 PCM player designed for ALSA (OSS output
module)
NH> ps: sorry messing with the BIOS didn't fix it.
No problem. If I'm not profusely thanking people for trying to help
with every message, it isn't because I'm not grateful.
5:43 p.m.
New subject: [linux-audio-user] Debian 2.6.14 alsa problems
On Friday 06 January 2006 19:54, Lee Revell wrote:
On Fri, 2006-01-06 at 18:13 +0100, Nigel Henry wrote:
Hi Lee. I suppose from a developers point of view Alsa 1.0.10 is ancient, but
I view Alsa 1.0.4, Alsa 1.0.6 as ancient. It's all a matter of perspective.
All the same it's nice to know that "Music" equates to "Synth" on
later
Alsamixer versions. Thanks. Nigel.
On Friday 06 January 2006 16:42, Laura Conrad
wrote:
Hi Laura. Lee Revell posted a reply to someone else on this thread. You
may have missed it. He says to make sure that "Synth" volume is up, so I
think that's saying that with the "Live" card, "Synth" equates
with
"Music" on my Audigy2.
The control is now called Synth. If it's called Music on your system it
means you have an ancient ALSA version and shopuld upgrade.
Lee
>>>> "NH" == Nigel Henry <cave.dnb(a)tiscali.fr> writes:
NH> Hi Laura On Debian Sarge/Etch, using Alsamixer v1.0.10 , the
only controls NH> affecting midi output are. Master; Front; and Music;
obviously with the NH> Audigy switch unmuted also.
For the SBLive, 1.0.10 doesn't seem to have either Front or Music.
I'm pretty sure Music is now Synth; does anyone know what Front turned
into?
NH> I'm using Kmid, and Emu10k1 Wavetable Emu10k1 Port2 -ALSA
device (shown in NH> Kmids midi config), and the other 3 ports are ok.
Kmid looks like it would be really nice, if it would only play the
sound.
NH> Souncard is: Audigy2 soundblaster (emu10k1). Chip: Sigmatel
NH> STAC9721/23
Card: SBLive! Platinum [CT4760P]
Chip: TriTech TR28602
NH> Kernel: 2.6.11-1-386
Kernel: 2.6.14-2-386
NH> Alsa version: 1.0.8 (with the 2.6.11 kernel)
[~]# cat /proc/asound/version
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12
08:13:09 2005 UTC).
NH> Alsa components installed:
NH> alsa-base 1.0.10-3
NH> alsa-modules-2.4-27-2-386 1.0.10+1 (I have a 2.4 kernel, as
well as the NH> 2.6)
NH> alsa-oss 1.0.10-1
NH> alsa-utils 1.0.10-1
[~]# dpkg -l alsa-modules-2*
||/ Name Version Description
+++-===========================-===========================-===========
==== ======================================================= ii
alsa-base 1.0.10-3 ALSA driver configuration files
ii alsa-modules-2.4.27-1-686 1.0.6a+4 Advanced
Linux Sound Architecture (drivers) ii alsa-oss
1.0.10-1 ALSA wrapper for OSS applications ii alsa-utils
1.0.10-1 ALSA utilities ii alsaplayer
0.99.76-0.2 PCM player designed for ALSA ii
alsaplayer-common 0.99.76-0.2 PCM player
designed for ALSA (common files) ii alsaplayer-gtk
0.99.76-0.2 PCM player designed for ALSA (GTK version) ii
alsaplayer-oss 0.99.76-0.2 PCM player designed for ALSA
(OSS output module)
NH> ps: sorry messing with the BIOS didn't fix it.
No problem. If I'm not profusely thanking people for trying to help
with every message, it isn't because I'm not grateful.
6989
days inactive
6991
days old
linux-audio-user@lists.linuxaudio.org
10 comments
4 participants
participants (4)
-
cmetzler＠speakeasy.net -
Laura Conrad -
Lee Revell -
Nigel Henry