11 Apr
2005
11 Apr
'05
1:34 p.m.
Hi,
I'm trying to get a RME Multiface working...
details:
2.6.11-7 kernel, freshly compiled from source
alsa-driver 1.0.9rc1
the snd_hdsp is loaded as a module, the firmware is not loaded (the
error led is still on).
pci_hotplug is enabled.
No difference whether I have the card in at boot-time or put it in later.
any suggestions would be welcome!
sincerely,
Marije
11 Apr
11 Apr
2:33 p.m.
Hoi Marije,
probably a bit more info would help, but I'll try with what's here.
I assume this is a PCMCIA card? If so then it's pretty much the same
setup I have. What I used was Alsa drivers 1.0.8 from the
alsa-project.org site, compiled manually, with a 2.6.10 kernel. Other
driver versions would not do it for me---don't know why--so you might
try this one in particular. You'll need the alsa-tools, alsa-utils and
alsa-firmware as well. For me, I had to eject and reinsert the card
after everything else is up and running. Did you also use the
"hdsploader" command? This can be run as a user (as long as this user is
in audio group).
Also of course check the PCMCIA support in your kernel. You'll need 32
bit enabled, might be safest to enable all the PCMCIA options.
Maybe you could provide some more info about your hardware if this
doesn't fix it right up.
best,
derek
Marije Baalman wrote:
Hi,
I'm trying to get a RME Multiface working...
details:
2.6.11-7 kernel, freshly compiled from source
alsa-driver 1.0.9rc1
the snd_hdsp is loaded as a module, the firmware is not loaded (the
error led is still on).
pci_hotplug is enabled.
No difference whether I have the card in at boot-time or put it in later.
any suggestions would be welcome!
sincerely,
Marije
--
derek holzer ::: http://www.umatic.nl
---Oblique Strategy # 121:
"Mute and continue"
5:36 p.m.
New subject: Re[2]: [linux-audio-user] trying to get hdsp working
Hoi,
Monday, April 11, 2005, 8:44:21 PM, Derek wrote:
dh> probably a bit more info would help, but I'll try with what's here.
dh> I assume this is a PCMCIA card? If so then it's pretty much the same
dh> setup I have.
yes, PCMCIA.
dh> What I used was Alsa drivers 1.0.8 from the
dh> alsa-project.org site, compiled manually, with a 2.6.10 kernel. Other
dh> driver versions would not do it for me---don't know why--so you might
dh> try this one in particular. You'll need the alsa-tools, alsa-utils and
dh> alsa-firmware as well. For me, I had to eject and reinsert the card
dh> after everything else is up and running. Did you also use the
dh> "hdsploader" command? This can be run as a user (as long as this user is
dh> in audio group).
I also tried with the 2.6.11-lowlat. kernel from Ubuntu/Debian, ALSA
1.0.8. This also did not work.
Before, I got an error when running the hdsploader, that it could not
find the firmware file.
Now, I don't get to that point anymore (doesn't find the card at all,
it seems)
Maybe, I'll do a quick check whether I get the thing working under
Windows...
dh> Also of course check the PCMCIA support in your kernel. You'll need 32
dh> bit enabled, might be safest to enable all the PCMCIA options.
I have.
dh> Maybe you could provide some more info about your hardware if this
dh> doesn't fix it right up.
here's some info:
nescivi@polymatheus:~$ dmesg | grep Hammerfall
RME Hammerfall DSP: probe of 0000:03:00.0 failed with error -12
nescivi@polymatheus:~$ hdsploader
hdsploader - firmware loader for RME Hammerfall DSP cards
Looking for HDSP + Multiface or Digiface cards :
Card 0 : Intel 82801DB-ICH4 with AD1981B at 0xc0000c00, irq 11
Card 1 : Dummy 1
Card 2 : Intel 82801DB-ICH4 Modem at 0x2400, irq 11
nescivi@polymatheus:~$ cat /proc/asound/version
Advanced Linux Sound Architecture Driver Version 1.0.9rc1.
Compiled on Apr 11 2005 for kernel 2.6.11.7.
------
lsmod ¦ grep hdsp
snd_hdsp 56292 0
snd_hwdep 9952 1 snd_hdsp
firmware_class 10304 1 snd_hdsp
snd_rawmidi 26144 2 snd_hdsp,snd_usb_lib
snd_pcm 95816 9
snd_hdsp,snd_usb_audio,snd_intel8x0m,snd_dummy,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd 59844 22
snd_hdsp,snd_hwdep,snd_usb_audio,snd_usb_lib,snd_rawmidi,snd_seq_device,snd_intel8x0m,snd_dummy,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
snd_page_alloc 10180 4 snd_hdsp,snd_intel8x0m,snd_intel8x0,snd_pcm
6:15 p.m.
New subject: Re[3]: [linux-audio-user] trying to get hdsp working
Hi,
n> Before, I got an error when running the hdsploader, that it could not
n> find the firmware file.
n> Now, I don't get to that point anymore (doesn't find the card at all,
n> it seems)
n> Maybe, I'll do a quick check whether I get the thing working under
n> Windows...
just did so.
card works fine under Windows XP
after a warm reboot into linux, the error led is not burning anymore,
like it was before.
Still getting the same output from dmesg.
hdspmixer doesn't find the card, and it doesn't show up in the sound
card list (in the KInfoCenter), even though snd_hdsp is loaded.
any hints?
sincerely,
Marije
12 Apr
12 Apr
5:24 a.m.
New subject: Re[3]: [linux-audio-user] trying to get hdsp working
nescivi wrote :
Hi,
n> Before, I got an error when running the hdsploader, that it could not
n> find the firmware file.
n> Now, I don't get to that point anymore (doesn't find the card at all,
n> it seems)
n> Maybe, I'll do a quick check whether I get the thing working under
n> Windows...
just did so.
card works fine under Windows XP
after a warm reboot into linux, the error led is not burning anymore,
like it was before.
Still getting the same output from dmesg.
hdspmixer doesn't find the card, and it doesn't show up in the sound
card list (in the KInfoCenter), even though snd_hdsp is loaded.
any hints?
sincerely,
Marije
Hi Marije,
Can you please send the output of lspci -vv with the card inserted ?
Thanks,
Thomas
7:26 a.m.
thomas charbonnel wrote:
Can you please send the output of lspci -vv with the
card inserted ?
Thanks,
Thomas
With kernel 2.6.11-low-lat. (from Ubuntu/Debian), Alsa 1.0.8
(without rebooting)
0000:00:00.0 Host bridge: Intel Corp. 82855PM Processor to I/O Controller (rev 03)
Subsystem: IBM: Unknown device 0529
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+
>SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: <available only to root>
0000:00:01.0 PCI bridge: Intel Corp. 82855PM Processor to AGP Controller (rev 03) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+
FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
>SERR- <PERR-
Latency: 96
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: c0100000-c01fffff
Prefetchable memory behind bridge: e0000000-e7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
0000:00:1d.0 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1800 [size=32]
0000:00:1d.1 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
0000:00:1d.2 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 1840 [size=32]
0000:00:1d.7 USB Controller: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller
(rev 01) (prog-if 20 [EHCI])
Subsystem: IBM: Unknown device 052e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <available only to root>
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 81) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
>SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=02, subordinate=08, sec-latency=64
I/O behind bridge: 00004000-00008fff
Memory behind bridge: c0200000-cfffffff
Prefetchable memory behind bridge: e8000000-efffffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage Controller (rev
01) (prog-if 8a [Master SecP PriP])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 1860 [size=16]
Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K]
0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev
01)
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1880 [size=32]
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
AC'97 Audio Controller (rev 01)
Subsystem: IBM: Unknown device 0554
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 18c0 [size=64]
Region 2: Memory at c0000c00 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at c0000800 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>
0000:00:1f.6 Modem: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem
Controller (rev 01) (prog-if 00 [Generic])
Subsystem: IBM: Unknown device 0559
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Capabilities: <available only to root>
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon
Mobility 7500] (prog-if 00 [VGA])
Subsystem: IBM: Unknown device 0530
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+
FastB2B+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <available only to root>
0000:02:00.0 CardBus bridge: Texas Instruments PCI4520 PC card Cardbus Controller (rev
01)
Subsystem: IBM: Unknown device 0552
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 20400000-207ff000 (prefetchable)
Memory window 1: 20800000-20bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:02:08.0 Ethernet controller: Intel Corp. 82801BD PRO/100 VE (MOB) Ethernet Controller
(rev 81)
Subsystem: IBM: Unknown device 0522
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0204000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 8000 [size=64]
Capabilities: <available only to root>
0000:03:00.0 Multimedia audio controller: Xilinx Corporation RME Hammerfall DSP (rev 0a)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20800000 (32-bit, non-prefetchable) [disabled] [size=64K]
With kernel 2.6.11-7, alsa 1.0.9rc1
0000:00:00.0 Host bridge: Intel Corp. 82855PM Processor to I/O Controller (rev 03)
Subsystem: IBM: Unknown device 0529
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+
>SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: <available only to root>
0000:00:01.0 PCI bridge: Intel Corp. 82855PM Processor to AGP Controller (rev 03) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+
FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
>SERR- <PERR-
Latency: 96
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: c0100000-c01fffff
Prefetchable memory behind bridge: e0000000-e7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
0000:00:1d.0 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1800 [size=32]
0000:00:1d.1 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
0000:00:1d.2 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 1840 [size=32]
0000:00:1d.7 USB Controller: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller
(rev 01) (prog-if 20 [EHCI])
Subsystem: IBM: Unknown device 052e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <available only to root>
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 81) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
>SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=02, subordinate=05, sec-latency=64
I/O behind bridge: 00004000-00008fff
Memory behind bridge: c0200000-cfffffff
Prefetchable memory behind bridge: e8000000-efffffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage Controller (rev
01) (prog-if 8a [Master SecP PriP])
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 1860 [size=16]
Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K]
0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev
01)
Subsystem: IBM: Unknown device 052d
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1880 [size=32]
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
AC'97 Audio Controller (rev 01)
Subsystem: IBM: Unknown device 0554
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 18c0 [size=64]
Region 2: Memory at c0000c00 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at c0000800 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>
0000:00:1f.6 Modem: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem
Controller (rev 01) (prog-if 00 [Generic])
Subsystem: IBM: Unknown device 0559
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Capabilities: <available only to root>
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon
Mobility 7500] (prog-if 00 [VGA])
Subsystem: IBM: Unknown device 0530
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+
FastB2B+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <available only to root>
0000:02:00.0 CardBus bridge: Texas Instruments PCI4520 PC card Cardbus Controller (rev
01)
Subsystem: IBM: Unknown device 0552
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 20400000-207ff000 (prefetchable)
Memory window 1: 20800000-20bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:02:08.0 Ethernet controller: Intel Corp. 82801BD PRO/100 VE (MOB) Ethernet Controller
(rev 81)
Subsystem: IBM: Unknown device 0522
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+
FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0200000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 8000 [size=64]
Capabilities: <available only to root>
0000:03:00.0 Multimedia audio controller: Xilinx Corporation RME Hammerfall DSP (rev 0a)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20800000 (32-bit, non-prefetchable) [disabled] [size=64K]
8:20 a.m.
Marije Baalman wrote :
0000:03:00.0 Multimedia audio controller: Xilinx
Corporation RME Hammerfall DSP (rev 0a)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20800000 (32-bit, non-prefetchable) [disabled] [size=64K]
0000:03:00.0 Multimedia audio controller: Xilinx
Corporation RME Hammerfall DSP (rev 0a)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR-
FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20800000 (32-bit, non-prefetchable) [disabled] [size=64K]
>
Memory is marked as disabled where it shouldn't. You'll have to tweak
your pcmcia config. Maybe you could try googling for cardbus problems
for people with the same machine as you.
Apart from this, stick with 1.0.9rc*, 1.0.8 is broken for the hdsp.
Thomas
5:35 a.m.
Still getting the same output from dmesg.
hdspmixer doesn't find the card, and it doesn't show up in the sound
card list (in the KInfoCenter), even though snd_hdsp is loaded.
any hints?
Hm, I *think* hdsp stuff needs to get probed and loaded early; Thomas
Charbonnel (thomas(a)undata.org) would know.
As you seem to have "alias snd-card-0 snd-intel8x0" in
your /etc/modules.conf your internal sound card gets initialized first.
Personally I would try to disable that and see what happens. Like
commenting out the snd-card-0 stuff in modules.conf or turning the
device off in BIOS.
Plus try getting your hdsp on irg 10, has higher priority. Run hdspconf
before hdspmixer and leave them open, they're not in the way.
Wolfgang, monkey-typing
5:57 a.m.
Hi again,
Wolfgang Woehl wrote:
As you seem to have "alias snd-card-0
snd-intel8x0" in
your /etc/modules.conf your internal sound card gets initialized first.
I would agree with Wolfgang. I always have my HDSP in the first
position, and the builtin card second. You have to mess around with a
few things when you don't have th HDSP in order to get things running on
the builtin card, but that's nothing that a few settings or a nicely
written .asoundrc can't fix.
d.
--
derek holzer ::: http://www.umatic.nl
---Oblique Strategy # 161:
"Trust in the you of now"
7:56 a.m.
Hi,
Wolfgang Woehl wrote:
commenting things out in modules.conf did not make a change
can't find in the BIOS where to turn the thing off.
Still getting
the same output from dmesg.
hdspmixer doesn't find the card, and it doesn't show up in the sound
card list (in the KInfoCenter), even though snd_hdsp is loaded.
any hints?
As you seem to have "alias snd-card-0 snd-intel8x0" in
your /etc/modules.conf your internal sound card gets initialized first.
Personally I would try to disable that and see what happens. Like
commenting out the snd-card-0 stuff in modules.conf or turning the
device off in BIOS.
Plus try getting your hdsp on irg 10, has higher
priority.
how can this be done?
I can set in the bios some stuff for the PCI cards, but have no clue
which one would be the right one.
They were numbered A to H (or something), but where how do I know which
one is the relevant one?
I have a IBM Thinkpad R51.
Run hdspconf
before hdspmixer and leave them open, they're not in the way.
neither finds the card...
sincerely,
Marije
8:28 a.m.
Marije Baalman wrote:
how can this be done?
Usually BIOS won't let you adjust IRQ on slots unless you answer 'no' to
the common question about 'are you using a pnp os'. This answer is
needed so BIOS assigns IRQ to devices on boot.
If BIOS don't let you assign IRQ to slots, then it's a matter of
swapping the card between different PCI slots and boot to check for
changes. This is usually the way to go on VIA chipsets.
Cordially, Ismael
8:36 a.m.
Hiho,
Ismael Valladolid Torres wrote:
Marije Baalman wrote:
I got the impression I could do it there, but have no clue which one is
the right one.
how can this be done?
Usually BIOS won't let you adjust IRQ on slots unless you answer 'no' to
the common question about 'are you using a pnp os'. This answer is
needed so BIOS assigns IRQ to devices on boot.
If BIOS don't let you assign IRQ to slots, then
it's a matter of
swapping the card between different PCI slots and boot to check for
changes. This is usually the way to go on VIA chipsets.
on a laptop this is not really an option.
sincerely,
Marije,
who is off googling now for PCMCIA problems with Thinkpad on Linux...
7266
days inactive
7267
days old
linux-audio-user@lists.linuxaudio.org
11 comments
6 participants
participants (6)
-
derek holzer -
Ismael Valladolid Torres -
Marije Baalman -
nescivi
-
thomas charbonnel -
Wolfgang Woehl