5 Jun
2010
5 Jun
'10
7:27 p.m.
Hey Patrick,
A word of warning: I haven't used amSynth at all, but the general principles
should be the same for all synths (generalised statement after generalised
statement!).
Basically your signal chain should go:
Oscillators -> Filter in -> Output
^
|
LFO
So you should feed the connect the oscillators to the Glame Lowpass input as
well.
Hope this makes sense!
Andrew
On Sat, Jun 5, 2010 at 6:11 PM, Patrick Shirkey
<pshirkey(a)boosthardware.com>wrote;wrote:
Hey Jeremy,
You sure that amsynth can't pull off a dubstep wobble bass?
The ingredients are relatively simple:
One lowpass filter
One LFO routed to the filter cutoff
One or Two Oscillators (I'd say having a sine or triangle an octave lower
or
at the same pitch as the other oscillator would be good here).
Then just filter the oscs quite low to remove the highs and set the LFO
running fairly fast-ish!
Just trying this setup out.
I have the following:
One lowpass filter
One LFO routed to the filter cutoff
LFO sine output -> Glame Low pass input
Check
One or Two Oscillators (I'd say having a sine
or triangle an octave lower
or at the same pitch as the other oscillator would be good here).
Que?
If you could clarify what the two oscillators are supposed to connect to
then I will build this example and post it here for everyone to play with.
Cheers.
Andrew.
On Sat, Jun 5, 2010 at 12:55 PM, Jeremy Jongepier
<jeremy(a)autostatic.com>wrote;wrote:
--
Patrick Shirkey
Boost Hardware Ltd.
Harry Van Haaren wrote:
_______________________________________________
Linux-audio-user mailing list
Linux-audio-user(a)lists.linuxaudio.org
http://lists.linuxaudio.org/listinfo/linux-audio-user
> With the help of some manuals I managed to
create a pretty ok Dubstep
> wobble bass in Yoshimi.
>
Cheers, there's too much going on at the moment for me to properly
check
it
out,
hopefully tomorrow I'll get to load it up though.
Glad there was such a response.. nice to have fellow "wobble bass"
peoples
about!
-Harry
Hello Harry,
You're welcome. And apparently my Dubstep instrument for Yoshimi was
good enough to get included in the latest Yoshimi release (thanks
Cal!!). If you want to control the wobbles it is possible to set the
Freq. LFO to zero and insert a Phaser effect in the chain and control
its LFO with NRPN messages. I took a look at it yesterday but apparently
my M-Audio Oxygen doesn't send out correct NRPN messages so Yoshimi
doesn't pick them up or I simply don't understand how to properly
program the right NRPN stuff). But I just got some new toys in (a
Behringer BCF2000 and a BCR2000), hopefully I'll get it to work with
those. Otherwise it would be an option to fire up an instance of
Rakarrack with a Phaser effect and control the LFO of the Phaser with
MIDI.
I've also taken a look at PHASEX but I don't grasp how everything is
routed internally so I just don't manage to get anything useful out of
it.
amSynth is not suited for Dubstep wobbles, it simply lacks the proper
functionality.
Maybe Bristol could pull the trick too.
For those who have no clue what this is about:
http://www.youtube.com/watch?v=IsQMpJ5lURQ (a classic that we spin
regularly at our parties)
Best,
Jeremy
_______________________________________________
Linux-audio-user mailing list
Linux-audio-user(a)lists.linuxaudio.org
http://lists.linuxaudio.org/listinfo/linux-audio-user