23 Apr
2013
23 Apr
'13
12:42 a.m.
On Mon, April 22, 2013 10:26 am, Chris Caudle wrote:
Most envy24 chipsets use the same reg as clock speed. So on that picture
there is a "Multi Track internal Clock" - "48000" if it is expanded
the
external clock will be above 96000 (if that is the top speed).
From: Gabbe
Nord <gabbe.nord(a)gmail.com>
Subject: Re: [LAU] S/PDIF in with ESI Juli@ and JACK
Here's a picture of my QASMixer with the inputs as well:
http://www.imagebam.com/image/fef059250185749
Where is the clock select in that picture? If you look on page 18 of the card manual showing the
(Windows?) utility
for controlling the card, there is a selection box to set using the
internal or external clock. To use the S/PDIF input you must select
external clock.
That is different from the Delta series then. Good to know. Though that
could be a SW limit and not HW, but I would guess in this case it is HW.
While it makes sense to lock to spdif to use it, there are cases where the
spdif input may be locked to this card from it's spdif output for example,
where not using spdif clock, but still using the info makes sense.
--
Len Ovens
www.OvenWerks.net
23 Apr
23 Apr
12:03 p.m.
New subject: S/PDIF in with ESI Juli@ and JACK
Hello!
Thanks for the replies!
I tried some more things:
* Putting the internal clock to S/PDIF in (or, IEC958 in) and then trying
both to use the hw:Juli,1 as input, and also to connect it using zita-a2j.
Using it as input, I get crashes in both JACK and QASMixer (is there any
other mixer I should use for this purpose instead?), and it even hung so
bad (an unkillable process) that I hade to restart the computer using the
power button. Using zita-a2j, it tries to sync (instead of just spamming
syncing like it did before), but it halts instantly and says it'll retry in
15 seconds (something about a too big of a timing difference, and that this
usually happens after freewheeling in JACK1 or something like that).
I tried to do this with the internal clock set to S/PDIF, and I also tried
de-activating the "Lock rate". No success though. I did however not try the
"Lock rate"-stuff too throughly.
Anything else I should try, that I've missed?
Thanks again!
On Tue, Apr 23, 2013 at 12:42 AM, Len Ovens <len(a)ovenwerks.net> wrote:
On Mon, April 22, 2013 10:26 am, Chris Caudle wrote:
Most envy24 chipsets use the same reg as clock speed. So on that picture
there is a "Multi Track internal Clock" - "48000" if it is expanded
the
external clock will be above 96000 (if that is the top speed).
From:
Gabbe Nord <gabbe.nord(a)gmail.com>
Subject: Re: [LAU] S/PDIF in with ESI Juli@ and JACK
Here's a picture of my QASMixer with the inputs as well:
http://www.imagebam.com/image/fef059250185749
Where is the clock select in that picture? If you look on page 18 of the card manual showing
the (Windows?) utility
for controlling the card, there is a selection box to set using the
internal or external clock. To use the S/PDIF input you must select
external clock.
That is different from the Delta series then. Good to know. Though that
could be a SW limit and not HW, but I would guess in this case it is HW.
While it makes sense to lock to spdif to use it, there are cases where the
spdif input may be locked to this card from it's spdif output for example,
where not using spdif clock, but still using the info makes sense.
--
Len Ovens
www.OvenWerks.net
_______________________________________________
Linux-audio-user mailing list
Linux-audio-user(a)lists.linuxaudio.org
http://lists.linuxaudio.org/listinfo/linux-audio-user
4235
days inactive
4236
days old
linux-audio-user@lists.linuxaudio.org
1 comments
2 participants
participants (2)
-
Gabbe Nord -
Len Ovens